AiM Expansions

The ECU Bridge Makes It Easy To Get Data From Your Car's ECU To Your AiM SmartyCam or AiM dash display (sold separately). With the AiM ECU Bridge With RS232/CAN Wiring, just a few simple wiring connections will get you up and running.

The new AiM GPS08 surface mount antenna module receives both GPS and GLONASS satellites signals for higher accuracy, faster power up and improved reliability in adverse conditions.

Can Increase The Analog Channel Capability On Your AiM MXL, EVO3, or EVO4 Data logger without occupying any analog channels!  AiM Thermo-Couple Hub For MXL, EVO3, EVO4 will let you do just that.

Extend The Capabilities Of Your AiM Solo DL, MXS, MXG, MXL, Pista / Pro Data Logger without occupying any more channels or running more cables to your dash. AiM 4-Port CAN Data Hub connects up to four CAN peripherals to each Data Hub. 

AiM LCU-One's can detect punctual Lambda value from 0.65 to 1.6 in older AiM dashes that use Race Studio 2 software. If you are using RaceStudio 3 for your MXM, Solo 2 DL, MXS, MXP, MXG, MXL2 you will need to use the CAN Connection LCU-1.

Can't reach the system buttons on your MXL2, MXG or MXS? The AiM Remote Button Interface offers you 6 contacts to eleminate the need for you to reach the push-buttons on your AiM MXL2, MXG and MSX. Now you can remotly access your four systems buttons, while the fifth is backlight control and the sixth for resetting the second (current stint) odometer. 

This stainless steel thread on dust cap fits all AiM 712 female connections. This AiM 712 dust cap fits all 3, 4, 5, and 7 pin female ports found on AiM Mychron's, AiM Evo data Loggers, AIM data hubs and more. We usually seal all open ports to eliminate any water damage in the wettest conditions.

This 712 AiM 5 pin threaded connector with male pins is a common cable end on many AiM CAN connections. If you are shortening or making custom length cables, the AiM 9904130005 Binder 712 5-pin/Male is a common part. 

The new AiM GPS09 surface mount antenna module receives both GPS and GLONASS satellites signals for higher accuracy, faster power up and improved reliability in adverse conditions.

The GPS09 Receiver connects to the AiM SmartyCam HD, HD Rev 2.0, HD Rev 2.1, HD GP 2.0 and HD GP 2.1 video cameras to provide GPS data such as speed, position, acceleration, and lap timing. This information can be overlaid directly on the video image as it records -- no hassles trying to synch the data to the video afterwards! 

The new AiM GPS09 surface mount antenna module receives both GPS and GLONASS satellites signals for higher accuracy, faster power up and improved reliability in adverse conditions.

ECU Bridge And RPM Bridge: These Two Systems Are Needed Whenever Engine Data Are to be visualized on a display or on an AiM SmartyCam HD video, if no recording is required.

Allows You To Connect Up To Four Analog Sensors (Or A Combination Of Analog Sensors and up to 2 digital sensors) to the CAN data port on your AiM MXL, EVO3, or EVO4 data logger. You can turn a very affordable dash into an incredibly powerful data logger with AiM Channel Expansion Hub For MXL, EVO3, EVO4. 

The LCU-One Lambda Controller uses the proven wideband Bosch LSU 4.9 oxygen sensor to send Lambda values to your AiM MXL, MXG, MXS, MXL2 dash, EVO3 / EVO4 data logger, SoloDL lap timer, or MyChron5 and 4 kart dash.

AiM MemoryKey Stores Data From Your AiM MXL, EVO3, or EVO4 Data Logger For download later, freeing the AiM data logger from having to connect directly to a computer.

AiM LCU-One's Can Detect Punctual Lambda Value From 0.65 to 1.6, Offering You An extremely precise measurement useful for engine tuning. AiM LCU-One Lambda controller with Analog connection allows you to perfectly tune the carburation of your engine as well as keep it at its best, appreciably improving your car performances. 

AiM MemoryKey Extension Port when the CAN port is not easily accessable. Used by every pro team to let the data team download the data without being in the cockpit. 

The ECU Bridge Makes It Easy To Get Data From Your Car's ECU To Your AiM SmartyCam or AiM dash display (sold separately). With the AiM ECU Bridge With RS232/CAN Wiring, just a few simple wiring connections will get you up and running.

AiM Memory Module for MXL2, MXG, MXS, MXM, EVO4S, EVO5, and all modern AiM Dash loggers. Your new AiM dash came with WiFi download capability but if you need to download your data during a pitstop, the AiM memory module is your crew chief's new best friend. 

The AiM Shift Light Module uses one CAN channel and clearly displays your RPM, engine alerts and even other indicators. You can position your AiM Shift Light Module, with 10 independent RGB LED's, on your dash panel when your AiM dash shift lights are not in primary view.  

Do you have an AiM Dash like the MXS, MSM, MXG, Pista or MXL and want to run multiple devices like SmartyCam HD's or other power usage items? Then the AIM 2 port powered CAN Data Hub is for you. If you use an ECU bridge or are powering your SmartyCam(s) from your 5 pin cable (using ECU Power), you now can have a more stable power supply to run your cameras for an extended duration.

AiM specially designed wiring and cables for the connection of all AiM electronic components to be useful and fundamental.

The new AiM GPS09 roof mount antenna module receives both GPS and GLONASS satellites signals for higher accuracy, faster power up and improved reliability in adverse conditions.

This is a CAN-programmable 12-button panel compatible with AiM PDM systems (PDM08 and PDM32). This keypad comes pre-configured for use with AiM protocols and is ready to be programmed through AiM's RaceStudio software. The buttons measure 15mm size and the overall panel size is 181.5mm x 70.0mm x 16.3mm (7.14" x 2.75" x 0.64").

The AiM keypad inserts allow you to label & use your AiM CAN Keypad. These are a required add-on to operate each button.

This is a CAN-programmable 8-button panel compatible with AiM PDM systems (PDM08 and PDM32). This keypad comes pre-configured for use with AiM protocols and is ready to be programmed through AiM's RaceStudio software. The buttons measure 15mm size and the overall panel size is 123.5mm x 70.0mm x 16.3mm (4.86" x 2.75" x 0.64").