Bell Racing | Bell Helmet Accessories | Genuine Bell Helmet Parts

Replacement Parts

Genuine Bell Helmet replacement parts and accessories like shield keys, breath anti-fog deflectors, new eyeport foam and more to improve your most important piece of safety equipment. Bell accessories and parts fit perfectly every time and have been on every podium at every track there is. Trust Bell Racing Accessories to keep you safe.

Bell Shield Hex Wrench Key
In Stock
The 2 Sided Bell Shield Hex Wrench Key has 2 Different Sizes for easy removal of your helmet shield.
$12.95
Bell Detent to SRV Pivot Conversion Kit
In Stock
The Bell Detent-to-SRV Pivot conversion kit allows the installation of the current SRV-style Bell Shield to previous generation Detent-style helmets, usually SA2005 and some early SA2010 full face helmets.
$29.95
Bell Helmet Breath Deflector
In Stock
Easy To Install And Remove, Bell's Helmet Breath Deflector Is Engineered to direct breath down and away from the face's shield to minimize fogging.
$19.95
Bell Forehead Vent Kit (V.10) Two Pieces
Last items in stock
Bell Helmet Forehead Vent Replacement Kit  features the same "sliding door" design as the original. This new design is the same as supplied on SA2010 Bell full-face helmets (except BR.1 and forced air helmets). The sides are sloped for improved aerodynamics over the older version. The hole size is unchanged, but the overall footprint is 5/64" (2mm) larger in both length and width.
$14.95
Bell Helmet Eyeport Foam Kit
In Stock
Repair Your Ripped or Torn Eyeport Foam With This Universal Replacement Kit. Just peel and stick to your helmet for a "like new" seal.
$14.95
Bell HP5/GT.5 Carbon Peak Visor
Last items in stock
The Bell Carbon Peak Visor for Bell SA2015 HP5 and GT.5 helmets. This fits your Bell HP5 and GT.5 Touring SA2015 Helmets perfectly and keeps the sun out of your eyes during those bright days.
$89.95
Bell Rubber Edge Molding Kit (Thin)
In Stock
Fitting Bell SA2010 and SA2015 helmets, the Bell rubber molding kit is the Bell helmet bottom rubber trim piece. If you place your helmet on your Hans device and then into its bag, the Hans grip tape will chew through this rubber gasket. Also if you are a kart racer with an aggressive angled seat, your suit may wear into this gasket also. 
$24.95
Bell Pivot Kit SV Series - Fits SE03/SE05 Shields Black
Last items in stock
The Bell Black SV (SE03/SE05) Pivot Kit & Screws fits Bell SA2015 and SA2010 Helmets. Fits Bell SA2015 GP.3, GTX.3, GT5, and HP5 helmets. Also fits HP3, HP5, HP Star Infusion and GT.5 Touring SA2010 Helmets.
$24.95
Bell Tear Off Post Kit - Aluminum
TearOff Post Kit By Bell in Natural Aluminum Holds Tearoffs Securily Through The Toughest Conditions. Fits all SRV and Detent Shields.
$12.95
Bell Helmet Top Plate Kit- White-Star Infusion/BR.1
Bell's  Star Infusion and BR.1 have been designed with modular air ports allowing the racer to run a traditional style helmet, top forced air helmet, or side forced air helmet. This is the replacement piece for a traditional style helmet set-up. (white)
$39.95
Bell Helmet Top Plate Kit-Matte Black-Star Infusion/BR.1
Bell's  Star Infusion and BR.1 have been designed with modular air ports allowing the racer to run a traditional style helmet, top forced air helmet, or side forced air helmet. This is the replacement piece for a traditional style helmet set-up. (matte black)
$39.95
Bell Rubber Edge Molding Kit (Medium)
Fitting Bell SA2010 and SA2015 helmets, the Bell rubber molding kit is the Bell helmet bottom rubber trim piece. If you place your helmet on your Hans device and then into its bag, the Hans grip tape will chew through this rubber gasket. Also if you are a kart racer with an aggressive angled seat, your suit may wear into this gasket also.
$24.95
Bell Helmet Top Plate Kit- Carbon HP Star Infusion
Bell's HP Star Infusion Carbon Fiber Replacement Top Plate is attached to the top our your helmet by nylon break-away screws. If your Bell HP Star Infusion needs a replacement top cover plate in true carbon fiber, this is the genuine Bell OEM replacement. 
$49.95
Bell Manual Lever Vent Kit - GP3/M8 V16 Clear - 3 pc
The Bell GP3 & M8 helmets feature 3 vents on top that can be closed off individually with the integrated lever on each vent. This 3-pack of replacement vents allows you to replace these vents if they break.
$34.95