AiM PDM CAN-Configurable Keypad - 8-Button
AiM Sports AiM PDM CAN-Configurable Keypad - 8-Button $350.00
AiM PDM CAN-Configurable Keypad - 8-Button PDM Buttons sold separately here This is a CAN-programmable 8-button panel compatible with AiM PDM systems (PDM08 and PDM32). This keypad comes pre-configured for use with AiM protocols and is ready to be programmed through AiM's RaceStudio software. The buttons measure 15mm size and the overall panel size is 123.5mm x 70.0mm x 16.3mm (4.86" x 2.75" x 0.64"). AiM PDM CAN-Configurable Keypad - 8-Button Details: Manufacturer: AiM Sports Manufacturer part number: KEY008 Weight: 170g (6 oz) Connector: Deutsch 6-pin, DT04-4P Supply voltage: 12-24Vdc, Nominal 8-32Vdc Standy current: <50mA Communications BUS: RS485, CANopen J1939 Operating temperature: -40C to +70C Thermal shock: -40C to +85C Salt spray standard: ASTMB117 Chemical resistance: Dirt, Engine cleaner, Isopropyl alcohol, Multi-purpose cleaner, Muriatic acid Waterproof rating: IP67 Each button function and backlight is programmed using AiM software and can be set up as momentary, toggle, or multi-position. Once programmed install the button insert for each button. Rear connector is a motorsport-grade Deutsch 6-pin connector wired for power, ground, CAN high, CAN low, TxRx-, and TxRx+.
AiM Sports GPS09 Module
AiM Sports AiM Sports GPS09 Module $349.00
AiM Sports GPS09 Module The GPS09 module from AiM further expands the track mapping abilities of AiM data loggers and dash loggers. In addition, the GPS09 allows lap timing (even split times) without the use of trackside beacons, storing data for up to 50 tracks with up to 5 splits per track. The GPS09 can also calculate and log speed, lateral and longitudinal g-forces, and of course vehicle position.The GPS09 is the latest version, boasting a quicker 25 Hz sampling rate (up from 10 Hz) and positional accuracy to less than one foot (down from 2 meters). It also takes full advantage of Race Studio 3's integration of GPS, video, and data. Simple to install: Just connect the CAN cable to your dash and mount the magnetic-backed GPS antenna to your vehicle roof. The GPS unit willl even automatically configure itself during start-up! The GPS09 connects via a 5-pin 712 screw-in conncetor and is compatible with current-generation AiM MXL2/ MXG/MXP/MXS auto dashes, EVO4S/EVO5 data loggers, and SmartyCam HD GP 2.2. Choose a cable length to suit your installation: 1.3m (4 ft) is appropriate for most formula cars and bikes. 4m (13 ft) is long enough for sedans. SmartyCam Note: Only the SmartyCam HD GP 2.2 takes this version. SmartyCam HD, SmartyCam HD GP, and SmartyCam HD 2.1 all require the AiM GPS09B which has a 4-pin connector. MXL / EVO3 / MyChron4 Note: This version is only compatible with the latest-generation loggers; it is not backwards-compatible with the first-gen MXL, the EVO3, or the MyChron4. Solo2/Solo2DL, MXm, and MyChron5 do not use an external GPS module; all GPS functions are internal. COMPATIBILITY GPS08 (five pin): MXL/MXL2, MXG, MXP, MXS, and MXm dashes, SmartyCam GPHD Rev 2.2, EVO3, EVO4S, and EVO5 GPS08B (four pin): SmartyCam GPHD Rev 2.1, SmartyCam GP Rev 2.1 Available in either Standard or Roof-Mount versions.
AiM Sports Channel Expansion Hub
AiM Sports AiM Sports Channel Expansion Hub $250.00
Aim Sports Channel Expansion Hub This compact CAN device provides virtually endless data acquisition system expansion options. The AiM Sports Channel Expansion Hub adds up to four freely configurable analog (or two digital and two analog) channels without occupying or modifying any of the existing system channels. By using advanced CAN technology, wiring is simplified from four cables into just a single connection, thereby reducing possible and unnecessary points of failure. Using the AiM Sports Data Hub, it's possible to connect to as many Channel Expansion Hubs as needed.
AiM Sports MyChron Expansion Channel Multiplier
AiM Sports AiM Sports MyChron Expansion Channel Multiplier $249.00
AiM MyChron Expansion The AiM MyChron Expansion is an add-on for the MyChron4 or MyChron5 Kart Racing Data Logging Dash. It plugs into the CAN expansion port on your MyChron dash to expand its capabilities. The Expansion has a single CAN expansion port plus four additional sensor inputs. All four inputs can accept common karting sensors (brake/throttle pedal position, temperature, steering angle, etc.). One of the four inputs can accept a speed sensor instead. Requires an external 12-volt power source such as your kart's battery. The MyChron Expansion channel multiplier improves MyChron5 and MyChron5 2T (and also MyChron4 and MyChron4 2T) performance, thanks to four additional channels and a further CAN bus connector. Through this last connector, the systems can be connected to LCU-One Lambda controller and SmartyCam HD (and to GPS and Data key for MyChron4 systems). Thanks to its specific wirings, MyChron Expansion powers the systems and their peripherals with an external battery, avoiding internal battery consumption. All channels are easily configurable as analog through the system menu to sample data coming from: Exhaust gas valve position sensor (very important to understand at which RPM value the exhaust port opens) Wheel speed sensor: the first input on the left can be configured also as digital input No contact brake pedal position sensor No contact throttle pedal position sensor Brake pressure sensor Water temperature or cylinder head temperature (PT100 thermo-resistor only) Steering angle potentiometer (to highlight over/under steering situations) Brake pedal potentiometer Throttle pedal potentiometer MyChron Expansion is a complete, value-for-money instrument for professional kart analysis. Call us with any questions you have about the MyChron Expansion from AiM Sports!
AiM Sports ECU Bridge with OBDII Connector
AiM Sports AiM Sports ECU Bridge with OBDII Connector $238.99
AiM ECU Bridge with OBDII, CAN/K Line Connector Connecting to the ECU allows the AiM unit access to data collected by your ECU (RPM, road speed, coolant temperature, and throttle position are typical; many ECUs offer much more information). Works with all AiM displays with a male 5-pin CAN connector, including the MXG, MXS, MSM, MXL, MXL Pro Dash Display, G-Dash Display, and Formula Car Wheel Display. SmartyCam requires the AiM 7-pin to 5-pin CAN Cable (Part No. MC-542, included with the SmartyCam). AiM ECU Bridge with OBDII CAN/K Line Connector Details: Manufacturer: AiM Manufacturer part number: X90BGGK12MA Alternate part number: X90BRIDGE01 Alternate part number: MC-401 CAN protocol for external modules (visors or SmartyCam HD) USB port for PC communication External power 8/18 V ECU Bridge CAN/K-line P-N-P OBDII kit* The ECU Bridge also features a special port for a USB cable (included) for easy connection to your computer for setup. ECU Bridge is available With CAN/RS232 connection, for direct installation on aftermarket ECUs. ECU Bridge and RPM Bridge: these two systems are needed whenever engine data are to be visualized on a display or on a SmartyCam HD video, if no recording is required. They are compatible with G-Dash and Formula/GT steering wheels, and of course with the SmartyCam HD on-board cameras. ECU Bridge is to be used in case the Engine Control Unit transmits data in the following hardware protocols: OBDII, CAN or RS232. AiM has developed hundreds of different protocols, to make compatibility with virtually all ECUs possible, either stock and after market ECUs. ECU Bridge has to be properly configured with Race Studio 2 software to communicate with the different visors/cameras on one side and ECUs on the other side. SmartyCam Installation Dash Display/Dash Logger Installation
AiM Sports ECU Bridge RS232- CAN Wiring
AiM Sports AiM Sports ECU Bridge RS232- CAN Wiring $238.99
AiM ECU Bridge with RS232 / CAN Wiring Connecting to the ECU allows the AiM unit access to data collected by your ECU (RPM, road speed, coolant temperature, and throttle position are typical; many ECUs offer much more information). Works with these AiM displays with a male 5-pin CAN connector: MXG MXS MSM MXL & MXL Pro G-Dash Display Formula Car Wheel Display SmartyCam requires the AiM 7-pin to 5-pin CAN Cable (Part No. MC-542, included with the SmartyCam). The ECU Bridge also features a special port for a USB cable (included) for easy connection to your computer for setup. ECU Bridge is available with CAN/RS232 connection, for direct installation on aftermarket ECUs. ECU Bridge and RPM Bridge are needed whenever engine data are to be visualized on a display or on a SmartyCam HD video, if no recording is required. ECU Bridge is used when the ECU transmits data via OBDII, CAN or RS232. AiM has developed hundreds of different protocols to make compatibility with virtually any ECU possible, stock or aftermarket. ECU Bridge has to be properly configured with Race Studio 2 software to communicate with the different visors/cameras on one side and ECUs on the other side. WIRING DETAILS: CAN protocol for external modules (visors or SmartyCam HD) USB port for PC communication External power 8/18 V
AiM Memory Module  for MXG / MXS / MXL2 / EVO4S / EVO5
AiM Sports AiM Memory Module for MXG / MXS / MXL2 / EVO4S / EVO5 $205.00
AiM Memory Module  for MXG / MXS / MXL2 / EVO4S / EVO5 Swap memory cards effortlessly to keep your driver data more organized. This unit allows you to easily swap memory cards to view driver data more efficiently between stints. AiM Memory Module  for MXG / MXS / MXL2 / EVO4S / EVO5 Details: Manufacturer: Aim Manufacturer part number: X08MMD040 Manufacturer Alternate Part Number: MC-720
AiM OBD Harness for MX-Series 1.2 Strada Dashes
AiM Sports AiM OBD Harness for MX-Series 1.2 Strada Dashes $159.99
AiM OBD Harness for MX-Series 1.2 Strada Dashes From AIM Sports, discover the specialized wiring harness compatible with the AiM MXS 1.2 Strada, MXP Strada, and MXG 1.2 Strada street dashboards. Designed to seamlessly connect via a 14-pin AMP connector, this harness ensures efficient power, ground, USB, and CAN expansions. Additionally, it facilitates a direct ECU link through the OBD-II diagnostic port. Ideal for production vehicles equipped with an OBD-II port, the harness supports both CAN and K-Line communication standards. Available for individual purchase. Note: Dashboard is sold separately."
AiM Data hub to connect SmartyCam 2.0 and older to a GPS09 Module
AiM Sports AiM Data hub to connect SmartyCam 2.0 and older to a GPS09 Module $99.00
AiM Data hub to connect SmartyCam 2.0 and older to a GPS09 Module Connect an AiM GPS09 module to a standalone SmartyCam HD / GP HD (until vers 2.1) with this special AiM powered data hub. AiM Data hub to connect SmartyCam 2.0 and older to a GPS09 Module Details: Manufacturer: AiM Manufacturer Part Number: X08HB2GK3 Wiring leads 1: Red 12v+ DC Wiring lead 2: Black Ground Port #1: Female 712 5 Pin Port #2: Female 712 5 Pin SmartyCam HD / GP HD (until vers 2.1) were designed to work with dedicated SmartyCam GPS modules, in particular when the camera was used in standalone. This GPS version is no longer available, thus users requiring to plug an AiM GPS module directly to their SmartyCam, shall use a standard GPS module and a specific 2 port DataHub, properly designed for this layout.  This SmartyCam/GPS DataHub (part n. X08HB2GK3) will host the GPS module and the SmartyCam CAN cable on its two ports; the DataHub will also provide an external 12V cable, to be connected to an external power supply, mandatory for this kind of use. Being a modified version, this SmartyCam/GPS DataHub will not offer the possibility to connect to an existing AiM datalogger, which in case will manage the GPS and the SmartyCam as usual. A standard two port DataHub will not work for this purpose.
AiM Sports Data Hub
AiM Sports AiM Sports Data Hub $77.00
Aim Sports Data Hub Extend The Capabilities Of Your AiM Solo DL, Solo 2 DL, MXS, MXG, MXL, Pista / Pro Data Logger without occupying any more channels or running more cables to your dash. AiM 4-Port CAN Data Hub connects up to four CAN peripherals to each Data Hub.  AiM 4-Port CAN Data Hub connects up to four CAN peripherals to each Data Hub. You can even "stack" Data Hubs, connecting up to four more hubs to each hub, multiplying the number of available connections! Accepts any AiM CAN accessory, including GPS, LCU-One Lambda Controller, Memory Key, or TC (Thermocouple) Hubs. Any channel can be selected for display on the dash. 15" cable. AiM 4-Port CAN Data Hub Details: Manufacturer: AiM Manufacturer part number: X08HUB010 Manufacturer alternate part number: MC-329 Connector 1: 712 Male (to dash) Connector 2/3/4/5: 712 Female (from SmartyCams or other CAN appliances)  This allows you to add multiple SmartyCams to your AiM system. Connection example:A V-8 engined car with EGT on every cylinder, two CHTs on each cylinder bank, one Lambda sensor on each cylinder bank, GPS, and a Memory Key would need three TC Hubs and two Data Hubs. The EGT and CHT thermocouples would all connect to the three TC Hubs. The TC Hubs and the GPS can all be connected to one Data Hub. That Data Hub would be connected, along with the two Lambda controllers and Memory Key, to a second Data Hub which would be connected to the dash or data logger.  Sixteen channels are monitored in addition to the channels still available in the dash or data logger!