Brey Krause

Brey Krause Harness Bar For The C5 Corvette This Harness Bar Fits The Following Cars: Chevrolet Corvette (1997-2004) Chevrolet Corvette Z06 (2001-2004) The Best Harness Bar for the C5 Corvette and Z06! The Brey Krause Model R-1115 Harness Bar for the C5 Corvette properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G loads of cornering and braking. Brey Krause bars are easy to install and remove, use only existing holes and mounting points, and will not damage the car in any way. Brey Krause C5 Corvette Harness Bar Details: Manufacturer: Brey Krause Manufacturer Model Number: R-1115 Fitments: C5 & C5 Z06 Corvette Harness Mount bar 1997-2004 Material: Type 304, stainless steel Finish: Powder coated in durable black wrinkle-finish Weight: 18 lbs. (8.2 kg) Installation: Bar attaches to factory mounting points in "B" pillars. Support rods attach to outside rear seat track mounting point.

Brey Krause C6/C7 Corvette Extra Low Seat Mount w/ Sub-Bar The Brey Krause R-9153 Driver-side seat mount offers a solution to the low roof-line of the C7 Chevrolet Corvette. The racing seat adapter places the seat rails at a slant, allowing the seat to be lower in a rearward position when combined with a Recaro Slider (sold separately). This slant allows the seat to sit higher when in a forward position (perfect for shorter drivers), while offering increased head clearance when adjusted rearward for taller drivers. The R-9153 bolts directly to the floor of the C7 Corvette, and combines with a Recaro slider to allow the installation of many seat options when used with Brey Krause side-mounts. Also compatible with the C6 Corvette if you are searching for additional head-room.The mounting kit comes complete with an adjustable integrated Sub-Bar for correct mounting of your 5 or 6 point harness system. The design also allows for the reuse of stock 3-point belts, with inboard/outboard lap belt mounting locations built in. Note: Brey Krause Seat brackets must be purchased separately - see Brey Krause R-906X series side mount brackets.PLEASE NOTE: Although this kit allows for the installation of many brands and models of seats, due to the extremely low roof-line and the tight confines of the C7 Corvette, many larger seats will not fit. Please contact one of our racing seat experts 888-748-7223 with questions relating to your particular installation needs. FEATURES: Materials: Aircraft-grade aluminum and Type 304 stainless steel (sub-bar) Finish: Black gloss powder coat Weight: 7.8 lbs. Models: Fits C6 and C7 coupes (2005 - 2019), including Z06 All necessary hardware included

Brey Krause C7 Corvette Lap Belt Mount The Brey Krause Model R-9160 Lap Belt kit allows the easy installation of lap belts to the factory C7 Corvette seat belt mounting points. One kit required per vehicle - a single kit works for both passenger and driver seats in the C7. Uses existing Corvette factory mounting points and will not interfere with factory seat belt. These brackets allow quick installation and removal for cars driven daily and are also used for autocross or driver education events, while leaving the factory seat belt functional. Technical Information: Part Number: R-9160 Material: 304 Stainless Steel Finish: Satin finish stainless steel Weight: 1.6 lbs. *Note: One kit required per vehicle. One kit works for both passenger and driver seats in C7. Will not disable use of factory belts.

Brey Krause Gen5 Camaro Seat Mount w/ Sub-Bar Everything you need in one place! Select driver or passenger side and add a sub-mount bar for each side! Brey-Krause manufactures high quality, performance driving accessories for a variety of automobiles. Innovative engineering and superior workmanship are hallmarks of the Brey-Krause automotive products. All Brey-Krause parts can be installed easily, without any modifications, using existing holes and factory mounting points to ensure that the value of the vehicle is never compromised. Whether the car is used on the road or the track, the Brey-Krause performance driving accessories set the standard in both engineering function and aesthetic design. Features: Material - Type 304 Stainless Steel Finish - Black gloss powder-coat; Satin finish Installation - Attaches to driver side factory seat mounting points R-9172 sub strap mount sold separately (see pull-down) Miscellaneous - Seat brackets must be purchased separately (see pull-down) Compatible side mounts when using Recaro sliders - For Sparco Seats to Recaro Sliders (These parts are made for but not limited to the mentioned seats.): R-9060 - Sparco Evo, Momo Super Cup, R-9061 - Sparco Evo 2, Evo 2+, Corsa, OMP HTE-XL Compatible side mounts when mounting direct to R-9170 - Side Mount Brackets for Sparco Seats (These parts are made for but not limited to the mentioned seats.):R-9071 - Sparco Evo, Pro 2000, R-9072 - Sparco Evo, Pro 2000, R-9073 - Sparco Evo 2, R-9074 - Sparco Evo 2, R-9761 - Sparco Evo 2 Plus, R-9762 - Sparco Evo 2 Plus, R-9075 - Sparco Evo 2 US, R-9076 - Sparco Evo 2 US Fitment: Chevrolet Camaro 5th Gen RACE SEATS ONLY! Does not work with OEM Recaro seats.

Brey Krause Gen6 Camaro Seat Mount w/ Sub-Bar Everything you need in one place! Select driver or passenger side and add a sub-mount bar for each side! Brey-Krause manufactures high quality, performance driving accessories for a variety of automobiles. Innovative engineering and superior workmanship are hallmarks of the Brey-Krause automotive products. All Brey-Krause parts can be installed easily, without any modifications, using existing holes and factory mounting points to ensure that the value of the vehicle is never compromised. Whether the car is used on the road or the track, the Brey-Krause performance driving accessories set the standard in both engineering function and aesthetic design. Features: Material - Type 304 Stainless Steel Finish - Black gloss powder-coat; Satin finish Installation - Attaches to driver side factory seat mounting points R-9172 sub strap mount sold separately (see pull-down) Miscellaneous - Seat brackets must be purchased separately (see pull-down) Compatible side mounts when using Recaro sliders - For Sparco Seats to Recaro Sliders (These parts are made for but not limited to the mentioned seats.): R-9060 - Sparco Evo, Momo Super Cup, R-9061 - Sparco Evo 2, Evo 2+, Corsa, OMP HTE-XL Compatible side mounts when mounting direct to R-9170 Driver- Side Mount Brackets for Sparco Seats (These parts are made for but not limited to the mentioned seats.):R-9071 Passenger - Sparco Evo, Pro 2000, R-9072 - Sparco Evo, Pro 2000, R-9073 - Sparco Evo 2, R-9074 - Sparco Evo 2, R-9761 - Sparco Evo 2 Plus, R-9762 - Sparco Evo 2 Plus, R-9075 - Sparco Evo 2 US, R-9076 - Sparco Evo 2 US Fitment: Chevrolet Camaro 6th Gen 2016+ RACE SEATS ONLY! Does not work with OEM Recaro seats.

Brey Krause R-1120 Harness Bar For Chevy C6 Corvette This Harness Bar Fits The Following C6 Corvettes: Chevrolet Corvette Coupe (2005-2013) Chevrolet Corvette Z06 & ZR1 (2006-2013) Chevrolet Corvette Grand Sport (2010-2013) The Brey Krause Model R-1120 Harness Bar for the C6 Corvette properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G loads of cornering and braking. Brey Krause bars are easy to install and remove, and will get you ready for the race track in just a few hours! Special Note: Because of mounting locations in the C6, the B-pillar plastic sail panel covers will require two holes to be drilled through them. Brey Krause provides plastic plugs to cover the holes if the bar is ever removed. Sail panel replacements can be ordered from your GM Dealer (Part 15277640 for driver side, and 15277641 for passenger side) if the plastic plugs are not the desired solution. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. Brey Krause C6 Corvette Harness Bar Details: Manufacturer: Brey Krause Manufacturer Part Number: R-1120 Material: Type 304, stainless steel Finish: Powder coated in durable black wrinkle-finish Weight: 17.2 lbs. (7.8 kg) Installation: Bar attaches to factory mounting points in "B" pillars.

Brey Krause R-1125 Harness Bar C7 Corvette Coupe This Harness Bar Fits C7 Corvette Coupes As Follows: Chevrolet Corvette Stingray & Z51 (2014-2019) Chevrolet Corvette Z06 (2015-2019) Chevrolet Corvette Grand Sport (2017-2019) Chevrloet Corvette ZR1 (2019) The Brey Krause Model R-1125 Harness Bar for the C7 Corvette Coupe (does not fit convertible models) properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G-force loads of cornering and braking. Brey Krause bars are easy to install and remove, and will get you ready for the track in just a few hours! Special Note: Because of mounting locations in the C7, the B-pillar plastic sail panel covers will require a slot on either side to be cut. Sail panel replacements can be ordered from your GM dealer if you don't want to cut the original panels (Part 23176134 for driver side, and part 23176135 for passenger side). Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. Brey Krause C7 Corvette Harness Bar Details: Manufacturer: Brey Krause Manufacturer Part Number: R-1125 Material: Type 304 stainless steel Finish: Powder coated in durable black wrinkle-finish Weight: 17.2 lbs (7.8 kg) Installation: Bar attaches to factory mounting points in B-pillars

Brey Krause R-1032 Harness BarPorsche 991 & 992 911 Carrera (except Targa) The Brey Krause Porsche 991/992 Carrera Harness Bar has been tested and certified by an independent lab to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev.MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements. The Brey Krause harness bar properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, this helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G-force loads of cornering and braking. Brey Krause bars are easy to install and remove, use only existing holes and mounting points, and will not damage the car in any way. Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. A mount really can't be relied on unless it has been tested to support the loads required by the National Highway Traffic Safety Administration. The Brey-Krause Harness Mount supported the loads specified by the National Highway Traffic Safety Admin. DOT for upper torso restraints in all automobiles. Tensile tests performed by an independent lab. Brey Krause Porsche 991/992 Harness Bar Details: Manufacturer: Brey Krause Manufacturer Part Number: R-1032 Material: Type 304, stainless steel Design Elements: Bar is designed to allow seat travel for tall drivers. Includes provisions for Seat Back Brace. Installation: Bar attaches to seat belt mounts & seat track hardware. Fitments: Porsche 991 & 992 911 Carrera (except Targa models must use Brey Krause R-1033 down tubes) Weight: 16 lbs. (7.3 kg) Finish: Powder coated in durable black wrinkle-finish 1 Notes 1 Harness bar pictured has a custom satin black powder coat. Brey Krause harness bars come standard with a wrinkle black powder coat.

Brey Krause R-1155 Harness BarFor Gen 5 & Gen 6 Camaro This Harness Bar Fits The Following Cars: Chevrolet Camaro, All (2016+) The Brey Krause Model R-1155 Harness Bar for the 2015 and later Chevrolet Camaro properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G loads of cornering and braking. Easy to install and remove, the Brey Krause R-1155 Harness Bar uses existing holes and mounting points, and requires no vehicle modification. Kit includes everything needed for a proper 4-point harness set-up, while allowing enough seat travel for the tallest of drivers. Brey Krause Camaro Harness Bar Details: Manuracturer: Brey Krause Manufacturer Part Number: R-1155 Material: Type 304, stainless steel Finish: Powder coated in durable black wrinkle-finish Installation: Bar attaches to factory mounting points in "B" pillars.

Brey Krause Sub Strap Mount The Brey Krause R-9030 works with BK's R-907x side mount brackets in conjunction with factory non-power 996/997/986/987* sliders to give you a straightforward solution to mounting your harness sub straps. A one-piece seat with anti-sub strap pass-through is required. Expertly crafted from 1.5" x 1" x 0.125" wall carbon steel tubing and powder coated in a black wrinkle-finish, the R-9030 is strong and durable. FEATURES: Fits all Porsche 996, 986 , most 997.1 and 987.1 with manual seat sliders* Material: 1.5" x 1" x 0.125" wall carbon steel Finish: Powder coated black wrinkle-finish Weight: 3 lbs. * Note: Factory non-power slider assembly from the 996/986 (and most 997/987s) required for installation. Will not fit 997.2 or 987.2 with tabbed sliders. Will not fit power-operated sliders.

Easily Install Sparco Racing Sliders In Your Porsche The Brey Krause R-9041 Seat Track Adapter Kit allows the installation of Sparco Seat Sliders to the floor of Porsche 911, Boxster, and Cayman models. This in turn allows the ability to adapt various Brey Krause R-906x Seat Side-Mount Brackets (sold separately) to the floor of your compatible Porsche. FEATURES TIG welded from 7-Ga. T304 stainless steel Adapts Sparco 00493 or Cobra sliders to Porsche 991/981/997/996/987/986 Satin-finish stainless steel Weight: 2 lbs. 6 oz.

Brey Krause Side-Mount Adapter & Sub Strap Bar The Brey Krause R-9044 Side-Mount Adapter with Integrated Sub-Strap Bar makes installing racing seats in your Porsche straightforward and painless. Designed for the Porsche 996, 997, Boxster or Cayman, the R-9044 does away with your OEM seat sliders, mounting the seat as low as possible in the car and removing excess weight. An integrated sub-strap bar is adjustable for proper 5 or 6-point sub-strap routings. Three front-to-rear fixed mounting points allow your Brey-Krause Side-Mount Adapters (not included) to be installed in several fore-aft positions. Best of all, the entire assembly can be quickly installed before a track event and just as easily removed when you're back home. Voila! The daily driving comfort of your stock seats plus the bolstering and safety of a racing seat when you're at the track.Brey Krause side-mount brackets can be added separately in the dropdown above, creating a ready-to-bolt-in racing seat system! FEATURES: Fits Porsche 911 Carrera (996/997), Boxster & Cayman (986/987) Material: Type 304 Stainless Steel Weight: 4 lbs. Finish: Satin Side mounts not included

Easily Install Racing Seats in your Porsche The Brey Krause R-9052 Seat Side Mount Adapters are designed to help install a multitude of side-mounting racing seats directly to the factory manual sliders used on many Porsche 991 and 981 cars. (Porsche OEM sliders are not included.) They also fit some later 997 & 987 Porsches equipped with similar tabbed sliders. Porsche factory sliders are known for their quality and strength. Along with their longer travel versus aftermarket sliders, they help retain the factory feel in your car. Brey Krause's innovative design allows the side mounts to be installed in four different positions. Combined with included spacers, they are compatible with a multitude of racing seats that are between 390 and 430mm wide. Slightly slotted side-mounting holes allow for fitment to the most popular seat manufacturers (Sparco, Recaro, OMP, Cobra, and more). The R-9052 is compatible with the Brey Krause R-9259 sub strap mount (available as an option above) for use with a five- or six-point racing harness. Made from 11-gauge T304 stainless steel Powder-coated in satin black Weight 1 lbs Fits all Porsche 991, 981 cars with OEM Manual Sliders (also fits later 997 & 987 cars with similar tabbed sliders) Fits Side-Mount racing seats between 390-430mm wide, and maintains factory seat belt mount. Download installation instructions here. Note: Porsche OEM Manual Sliders are required for complete seat installation and are not included. The R-9052 is not compatible with Porsche power seat sliders.

64.32 The Brey Krause R-9172 Sub Strap Mount is designed to mount directly to Brey Krause seat track adapters R-9170, and R-9171. This sub strap mount can be used with either driver- or passenger-side mounts.   FEATURES: T304 Stainless Steel Brushed Stainless Finish Weight 2 lbs. Side Mounts, Sliders, and Harness not included          

Adjustable Sub Strap Mounting Bar R-925X The Brey Krause R-9259 Sub Strap Mount is designed to mount directly to any Brey Krause variable-width side mounts and mounting adapters, including those designed to be used with seat sliders. The stainless steel bar is threaded on both ends to allow for length adjustment for seat widths up to 426mm while keeping the sub-strap guide centered. (For seats over 426mm, use the BK-R-9258). This sub strap mount can be used with either driver- or passenger-side mounts. FEATURES: T304 Stainless Steel Brushed Stainless Finish Weight 2 lbs. Side Mounts, Sliders, and Harness not included