458 Challenge

CMS RF1 DOT4 Racing Brake Fluid HIGH BOILING POINT WITHOUT THE HIGH PRICE RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid. RF1 RACING BRAKE FLUID DETAILS Typical dry boiling point: 328º C (622º F) Typical wet boiling point: 204º C (399º F) Exceeds DOT3 & DOT4 standards Bottle size: 500 ml (16.9 fl oz) Click Here for Product MSDS Sheet A WORD ABOUT FLUSHING RACING BRAKE FLUID All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Girodisc Brake Pad Spreader GDPS01 This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment. No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers. The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable. Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers. The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Brake Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

Pagid Racing Brake Pad Shape No. 8081 Fits the Following Vehicles: Make Model Build (Year) Front Rear Aston Martin DB11 [iron brakes] 16 - 23 X Aston Martin Vantage [iron brakes] street car 18 - X Audi RS6 [C6] 08 - 10 X Cadillac CTS-V [6-piston front caliper] 10 - 14 X Chevrolet Camaro SS [Gen 6] 6-piston Brembo calipers 16 - X Chevrolet Camaro ZL1 [Gen 5] 12 - 15 X Chevrolet Camaro SS 1LE [Gen 6] 6-piston Brembo calipers 16 - X Chevrolet Corvette C7 Z06 [iron brakes] 15 - X Chevrolet Corvette C8 Z06 [iron brakes] 23 - X Mercedes C 63 AMG [W204] 08 - 14 X Mercedes CLK 63 AMG Black Series 06 - 09 X Nissan R35 GT-R 08 - X Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. Pagid Racing Brake compounds are for steel (cast iron) rotors only unless otherwise noted. Pagid RSL 29 Compound: Pagid RS 14 Compound: The Pagid RS 14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. The Pagid RSL 29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. Pagid RSL 1 Compound: Used in GT cars, touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. RSL 1 is a low metallic resin bonded material containing steel and aramid fibers with very high heat resistance. It maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make this material appropriate for endurance races. Pagid RSC 1 Compound (Ceramic Rotors Only): A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RST 1 Compound: Used in Rally tarmac, GT cars and touring cars circuit racing (sprint), high down-force formula cars, NASCAR. Suitable for applications in heavy cars and where high torque is necessary against small diameter rotors. RST 1 has a very high friction level and high temperature resistance. It is a semi-metallic resin bonded material containing steel fibers. Cold friction and initial bite makes this material most appropriate for Rally and NASCAR applications. Pagid RST 3 Compound: RST 3 is a medium-high friction metal-ceramic compound containing steel fibers and is therefore the perfect complement of the RST product family. It captivates by its low heat conductivity. Rally tarmac and gravel, GT cars, touring cars and prototype circuit racing, formula cars and club racing. Wide range of applications due to it‘s combination of bite, friction and controllability.

A1-183 Girodisc 2pc Front Brake Rotors for Ferrari 458 Challenge FITMENT: Ferrari 458 Challenge, Front This Girodisc system is a direct replacement for the OEM front CCM rotors on the Ferrari 458 Challenge, although a different brake pad than OEM, with an annulus (pad swept area) of 66 mm or less, must be used1. We suggest the Pagid 8081, the most popular pad used with Girodisc rotors on the Ferrari 458 Challenge. The lower-annulus design of the Girodisc rotors keeps weight low without sacrificing braking performance. Girodisc two-piece floating rotors are lighter than OEM brake rotors. This reduction in rotational mass and unsprung weight allows for quicker acceleration, sharper steering, and faster suspension response. When used with Pagid or PFC performance brake pads and CMS RF-1 brake fluid (available from ), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of each Girodisc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair. 1 Note: These Girodisc rotors have a different annulus (pad swept area) than the OEM CCM rotors, to maintain their light weight. A brake pad with an annulus of 66mm or less must be used with these Girodisc rotors. The necessary pad shape is very common, found on the Nissan GT-R, Cadillac CTS-V, and most AMG Mercedes equipped with six-piston calipers. Features: • Built for racing reliability and consistent performance • Compatible with demanding track environments • Designed for perfect fit and easy installation FAQs: Is this part track-proven? Yes, it has been tested extensively under racing conditions. Does it require professional installation? While not required, professional installation is recommended for best performance. Will this fit my vehicle? Please refer to the fitment guide or contact us to confirm compatibility. Can I return this if it doesn’t fit? Yes, as long as it’s unused and in original packaging.

D1-128 GiroDisc Replacement Rotors FITS: FERRARI 458 CHALLENGE REPLACEMENT ROTOR DISC ONLY, DOES NOT INCLUDE ALUMINUM HAT. is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary.   The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

FITS: Ferrari 458 CHALLENGE   is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country.  We ship most products same or next business day to ensure we meet your delivery deadline.   The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc.  The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly.  By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency.  The Giro Disc rotors are lighter than OEM pieces.  The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response.   When used with Pagid or PFC performance brake pads, and RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum.  The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations.  The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.     The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance.  The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat.  The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.   The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.   Sold/Priced per pair.