Sparco Prime RF-10 8860 Supercarbon
Sparco Sparco Prime RF-10 8860 Supercarbon $2,999.00
Carbon helmet is homologated to the latest and highest FIA standard currently available making this helmet ready to use in any Motorsport discipline. The radically design carbon fiber shell is lightweight yet extremely strong, designed to withstand the most rigorous of accidents. Featuring a center visor locking mechanism which ensures a positive and safe closure. The chin ventilating system provides maximum air flow through the helmet ensuring the visor stays clear. Facility to accommodate an optional drinks system The visor (FIA approved) can be infinitely adjusted Supplied with factory fitted FHR posts The helmets ventilation is provided by air intakes situated on the front of the helmet that gives maximum air flow through the helmet ensuring the visor stays clear. The top ventilation acts as an exhaust to remove excess heat and condensation. The interior lining of the helmet is also removable which allows it to be washed very easily. Please note: The helmet is supplied with a clear visor, pictured with an optional dark smoke visor. FIA 8860-2018 & Snell SA2020 approved
Stilo ST5.1 GT Offshore Composite Helmet SA2020
Stilo Stilo ST5.1 GT Offshore Composite Helmet SA2020 $1,234.95
Stilo ST5.1 GT Offshore Composite Helmet SA2020 Note: This helmet includes communications in the left port. Stilo ST5 GT SA2020 Offshore Composite Helmet OrangeThe legend returns. The SA2020 Stilo ST5 GT helmet carries over everything that made the SA2015 version one of the most-loved helmets on the grid. Featuring the same tall eye-port and iconic side ports of the previous generation, the SA2020 ST5 GT from Stilo is worth getting excited about. This Offshore variant is already wired up for communications, and sports a bright orange shell, making it easy to spot. Stilo ST5 GT SA2020 Offshore Composite Helmet Orange Details:Manufacturer: StiloManufacturer part number: DA0702BF2TColor: OrangeM6 Nut Washer for HANS and other neck restraintsRating: SA2020Shield lock position: CenterReplaceable cheek pads: YesSizes: X-Small - XXX-Large (54 - 64 cm) This is a slightly heavier version of the ST5 Carbon helmet. It is made from a Kevlar Multi-Sandwich Fiber composite formed in an autoclave. It carries the same Snell SA2020 certification as the Carbon helmet, but the different material adds the weight. This different material yields a slightly heavier helmet, but at a reduced cost. The Snell SA2020 rating satisfies almost all racing sanctioning bodies’ requirements for helmet certifications.Available with integrated electronics, top- or side-forced air supply, hydration, or any combination of the three, this helmet offers flexibility while maintaining a clean cabin. There are no wires or hoses hanging down below the helmet – everything integrates seamlessly with the shell of the helmet.Features an M6 nut integrated into the shell to interface with Head and Neck Restraint Systems.All Stilo shields are treated with an anti-fog treatment and they do require special care. The best result we have by far is the Stilo Visor cleaner. Liberally spray the outside of the visor with the cleaner, and wipe in a single swipe with a microfiber towel until clean and dry. If fingerprints or dirt remain, repeat as needed. A back and forth wiping motion will tend to leave lint from the rag on the visor, so the single-pass works best. Repeat if necessary, but usually, one pass works great.Do not use Windex or any glass cleaner containing ammonia, as this can harm the anti-scratch coating on the outside of the visor, and the anti-fog coating on the inside of the visor. Note: There are many things we can do to adjust your helmet fit. Obviously the best thing is to come into our show room and try on the helmets, but many times, that is just not possible. One of the great things about Stilo helmets is the adjustability with helmet padding. Crown padding, Cheek padding and different ear muff sizes are all available. Please contact a DiscoveryParts helmet expert at 888-748-7223. INTEGRATED FLEXIBILITY The Stilo ST5.1 GT Composite is unsurpased in built-in flexibility. Its two side ports can be fitted with 3 different types of integrated communication electronics, forced air, helmet eject system, or a hydration system. Thanks to its innovative shell design, mounting and routing these options to the ST5.1 GT is sleek and seamless. When not in use, you don't even know the features are there. Whether you're using side-mounted communications, side air, or a built-in hydration kit for staying hydrated during long enduro stints, everything is neat, tidy and completely out of the way when not needed. Stilo offers simply the best modular racing helmet on the market. Industry-standard M6 threaded receivers are molded into the helmet shell to accommodate anchors for whichever head-and-neck restraint you use. Size Note: We have found that customers who typically wear a size 59 helmet are most comfortable in size 60, which uses the large shell. Please order accordingly. FEATURES: Includes noise attenuating earmuffs to reduce exterior noise and maximize effectiveness of communications with your crew. Select communications, forced air, hydration or eject options now, or add them later. New 2020 Snell Certification offers increased protection for all head forms at higher g-forces and speeds All Existing Stilo ST5 shields and other accessories work on new ST5.1 SA2020 helmets All sizes shown in centimeters An effective helmet is one that fits properly. Have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head, starting at a point about an inch above the eyebrows and around a point in the back of the head that results in the largest measurement, finally wrapping back around to the front. It's a good idea to take a few measurements and order your helmet based on the largest. Size Note: We have found that customers who typically wear a size 59 helmet are most comfortable in size 60, which uses the large shell. Please order accordingly. This helmet will ship to you with signature required for delivery.
Stilo ST5 GT in Matte Black w/ Iridium Red Visor
Sparco Sparco Air Pro RF-5W Martini Helmet SA2020 $1,199.00
Sparco Air Pro RF-5W Martini Racing Helmet   Spectacular limited edition Sparco Air Pro RF-5W features a beautiful Martini Racing paint scheme With its strong Carbon-Kevlar reinforced fiberglass shell, the Sparco RF-5W provides superior levels of comfort and safety. The Martini Racing livery takes the design of this phenomenal helmet to the next level. As a limited-edition Sparco exclusive, this helmet sets itself apart from any other in the paddock. Inside the helmet, the EPS padding and linings can be removed for washing, and can be re-positioned for more personalized fit and comfort. The helmet features exceptional ventilation with grilles on the front chin bar and six ducts on the top and back, keeping the driver cool and dry in the heat of racing. The RF-5W can also accommodate a drinking/hydration system. The visor features a center-positioned locking tab with a continual adjustment. Available in two different shell sizes (one for Small through Med-Large, another for Large on up) in order to get you the perfect fit. The Air Pro RF-5W Martini Racing helmet is supplied with factory fitted FHR / HANS posts. FIA 8859-2015 and Snell SA2015 approved. FEATURES Limited edition Martini Racing color scheme Strong and lightweight Carbon Kevlar reinforced shell Excellent ventilation to help keep you cooler and more focused FIA 8859-2015 and Snell SA2015 approved     An effective helmet is one that fits properly. Have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head, starting at a point about an inch above the eyebrows and around a point in the back of the head that results in the largest measurement, finally wrapping back around to the front. It's a good idea to take a few measurements and order your helmet based on the largest. This helmet will ship to you with signature required for delivery.
Arai GP-7 Helmet SA2020
Arai Arai GP-7 Helmet SA2020 from $1,069.95
Arai GP-7 SA2020 Helmet A driver favorite, the Arai GP-7 SA2020 helmet combines the most popular Arai features with new, improved upgrades. The GP-7 is constructed with Arai own PBcLc (Peripherally Belted Complex Laminate) shell construction and the same shell shape as the Formula 1 grade GP-7SRC model. New ventilation, a soft EPS liner, and a wider eye port for optimized peripheral vision are part of this new shell which gives the driver notable strength and flexibility. Replaceable cheek pads make racing comfortable for any driver, as do the three larger, closeable intake vents and two larger exhaust vents on the ventilation system. The GP-7 helmet is Snell SA2020 certified with factory-installed M6 washers/nuts. Drivers of any skill level can install their own Head and Neck Restraint system using a 6mm bolt. The FIA-8859-2015 certification sticker is applied to the interior liner of the helmet. POSITIVE SHIELD LATCH Simple yet effective, the positive latch mechanism on the GP-7 SA2020 helmet gives the driver solid shield latching, but is seamlessly integrated into the standard shield system for ease of use. NEW SHIELD PIVOT HARDWARE The GP-7 SA2020 features new shield pivot hardware with improved aerodynamics based on the updated track slider design. An increased peripheral field of view is featured on the 6 series, which surpasses the 5 series in visibility. The wider eye port, shield, and pivot hardware were all developed on the RC and adapted to the GP-7 SA2020 helmet. VENTILATION Increased airflow is key to the GP-7 SA2020 helmet design. This includes bigger, closeable intake vents with large 10mm holes in both front and rear. Larger rear vents also provide better airflow. M6 ANCHORS Drivers of all skill levels will appreciate the integrated, pre-installed M6 threaded washer/nut with 6mm threads which accepts a range of Head and Neck Restraint devices. A flat surface area around the mounting nut will let the anchor post base to rest flush along the surface of the helmet and around the full perimeter of the anchor base. FIA-8859-2015 certification sticker applied to the interior liner material. NEW CHINBAR The GP-7 SA2020 new, ergonomic chinbar and ridge at the bottom edge of the shell lowers the center of gravity and increases the structural integrity of the helmet. Additional improvements include a rise in the shell above the shoulders for increased clearance. EJECT READY CROWN PAD Arai's optional Eject system can be easily accommodated via a pre-cut pocket under the helmet crown pad. An effective helmet is one that fits properly. Have an assistant use a measuring tape, or a piece of string to measure the circumference of your head starting at a point approximately one inch above the eyebrows in front, around a point in the back of the head that results in the largest possible measurement, and finally wrapping back to the front. It is a good idea to take several measurements to make sure you have the largest one. This helmet will ship to you with signature required for delivery.
sale
Stilo ST5.1 GT Composite Helmet SA2020
00
DAYS
00
HRS
00
MIN
00
SEC
Stilo Stilo ST5.1 GT Composite Helmet SA2020 from $1,008.95 $1,122.00
Stilo ST5.1 GT Composite Helmet SA2020 The ST5.1 GT Composite is Stilo's Snell SA2020 version of their best-selling kevlar-carbon composite helmets. With an autoclave molded shell, the ST5.1 GT Composite offers far superior safety compared to fiberglass and most composites from their competitors. You get all this without sacrificing comfort or features, as Stilo continues to focus on minimizing weight and maximizing flexibility. With its large eyeport the Stilo ST5.1 GT Composite offers unsurpassed peripheral vision and all of the available tinted, mirrored, and iridium-colored visors (sold separately) have a center pinch-clip to make opening and closing easy, even while wearing nomex racing gloves. Although updated to meet the newest Snell SA2020 certification, the Stilo ST5.1 GT retains its FIA 8858-2015 homologation as well. This makes the helmet legal for nearly all road race usage (some sanctioning bodies require FIA 8860 homologated helmets. INTEGRATED FLEXIBILITY The Stilo ST5.1 GT Composite is unsurpased in built-in flexibility. Its two side ports can be fitted with 3 different types of integrated communication electronics, forced air, helmet eject system, or a hydration system. Thanks to its innovative shell design, mounting and routing these options to the ST5.1 GT is sleek and seamless. When not in use, you don't even know the features are there. Whether you're using side-mounted communications, side air, or a built-in hydration kit for staying hydrated during long enduro stints, everything is neat, tidy and completely out of the way when not needed. Stilo offers simply the best modular racing helmet on the market. Industry-standard M6 threaded receivers are molded into the helmet shell to accommodate anchors for whichever head-and-neck restraint you use. Size Note: We have found that customers who typically wear a size 59 helmet are most comfortable in size 60, which uses the large shell. Please order accordingly. FEATURES: Includes noise attenuating earmuffs to reduce exterior noise and maximize effectiveness of communications with your crew. Select communications, forced air, hydration or eject options now, or add them later. New 2020 Snell Certification offers increased protection for all head forms at higher g-forces and speeds All Existing Stilo ST5 shields and other accessories work on new ST5.1 SA2020 helmets All sizes shown in centimeters OTHER STILO ST5.1 VERSIONS: For the carbon fiber version see Stilo Helmets ST5.1 GT Carbon Helmet. For the FIA 8860-2018 versions see the ultralight Stilo Helmets ST5 GT ZERO 8860-2018 Carbon Helmet, or the non-ZERO Stilo Helmets ST5 GT 8860-2018 Carbon Helmet at nearly half the cost. An effective helmet is one that fits properly. Have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head, starting at a point about an inch above the eyebrows and around a point in the back of the head that results in the largest measurement, finally wrapping back around to the front. It's a good idea to take a few measurements and order your helmet based on the largest. Size Note: We have found that customers who typically wear a size 59 helmet are most comfortable in size 60, which uses the large shell. Please order accordingly. This helmet will ship to you with signature required for delivery.
Sparco Air Pro RF-5W 1977 Helmet SA2020
Sparco Sparco Air Pro RF-5W 1977 Helmet SA2020 $999.00
Sparco Air Pro RF-5W 1977 SNELL SA2020 The Sparco helmet line is a result of over 40 years of research and development experience, including wind tunnel testing. The new range was designed to meet the requirements of the new Snell SA2020 and FIA 8859-2015 ratings. The 2020 type-approval introduces new impact requirements, the helmets need to dissipate large amounts of energy in different ways. To meet these requirements Sparco is introducing new innovations for driver safety and comfort. All shells now have layers of carbon-Kevlar for greater strength. The helmets have also been wind-tunnel tested to maximize exterior vent placement and flow. The EPS interiors and padding have also been redesigned for increased airflow and driver comfort. Sparco also introduces a new size: Medium/Large. This M/L size takes advantage of using the smaller shell which is lighter and more compact. AIR PRO 1977 The Air Pro 1977 is a painted version of the Air Pro RF-5W. This retro inspired helmet has a white base with blue or red stripes and has a clear coat painted over. The Air Pro 1977 features a carbon-Kevlar/fiberglass construction. It includes a wider eye opening that can be used for open wheel or closed cockpit driving. Multiple exterior vents increase circulation to a redesigned interior. The interior has channels which not only cool the driver, but has additional channels which route air towards the visor, which reduces the chance of visor fogging. Air Pro 1977 has removable, washable padding that can be repositioned for a comfortable fit. All interior seams have been removed from areas where greater pressure is exerted on the head. The Air Pro 1977 has been designed to accommodate a drink tube and an intercom system. Available in white with blue or red stripes. Sizes XS to XXL (including size M/L). Air Pro 1977 has Hans clips pre-installed. SNELL SA2020 and FIA 8859-2015 approved. TECHNOLOGY Painted Retro design Light-weight carbon-Kevlar/fiberglass construction New Medium/Large size which uses the lighter and more compact shell Anodized aluminum chin strap hardware Removable, washable lining Wind tunnel optimized venting with anti-fog air channels Pre-molded interior to accommodate drink tubes and an intercom system SNELL SA2020 and FIA 8859-2015 approved   An effective helmet is one that fits properly. Have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head, starting at a point about an inch above the eyebrows and around a point in the back of the head that results in the largest measurement, finally wrapping back around to the front. It's a good idea to take a few measurements and order your helmet based on the largest.
Bell RS7 Pro Helmet SA2020
Bell Bell RS7 Pro Helmet SA2020 from $899.95
    Bell Racing Helmets RS7 Pro SA2020 Helmet Based on the HP7 design and featuring a lightweight carbon composite shell using Bell high-pressure proprietary molding system, the RS7 uses and innovative shell and shield design to improve acoustic comfort, aerodynamic performance and energy absorbing capabilities. The sleek, modern design features an advanced ventilation system with 14 air-intake and extraction channels that can be used with or without air-intake covers (available separately). The RS7 double screen anti-fog (DSAF) visor and rubber gasket seal ensured air, water and dust will not enter the eyeport   CERTIFICATIONS: Snell SA2020 FIA 8859-2015 FEATURES: Lightweight carbon composite shell. Advanced multi-density, multi piece liner to maximize energy absorption and impact performance. Optical grade injection molded Double Screen Anti-Fog (DSAF) visor. Powerful and effective top and chin bar ventilation system with 14 air intake and extraction channels. Shell and shield design optimized to improve aerodynamic performance. Integrated channels in face piece offer multiple options to install drink tube and radio systems. Air intake, side air extractors, rear spoiler, top and chin bar gurneys available separately. Top air attachments available separately for use with external cooling systems. Factory installed HANS posts. Synthetic rubber gasket seal to prevent dirt and water entering the helmet. Shield and pivot kit: SE07, SV(SE07). Solid colors: White or Matte Black. Graphics colors: Stamina Grey or Stamina Red. Sizes: 6 3/4 (54) to 7 5/8+ (61+). All sizes shown in centimers.     IN THE BOX: Bell RS7 Pro SA2020 Clear SE07 DSAF shield Draw string helmet bag HANS post anchors installed   This helmet will ship to your with signature required for delivery.
Sparco Air Pro RF-5W Helmet SA2020
Sparco Sparco Air Pro RF-5W Helmet SA2020 $899.00
Sparco Air Pro RF-5W SNELL SA2020 The Sparco helmet line is a result of over 40 years of research and development experience, including wind tunnel testing. The new range was designed to meet the requirements of the new Snell SA2020 and FIA 8859-2015 ratings. The 2020 type-approval introduces new impact requirements, the helmets need to dissipate large amounts of energy in different ways. To meet these requirements Sparco is introducing new innovations for driver safety and comfort. All shells now have layers of carbon-Kevlar for greater strength. The helmets have also been wind-tunnel tested to maximize exterior vent placement and flow. The EPS interiors and padding have also been redesigned for increased airflow and driver comfort. Sparco also introduces a new size: Medium/Large. This M/L size takes advantage of using the smaller shell which is lighter and more compact.   TECHNOLOGY Lightweight carbon-kevlar/fiberglass construction New Medium/Large size uses lighter, more compact shell Anodized aluminum chin strap hardware Removable, washable lining Wind tunnel optimized venting with anti-fog air channels Pre-molded interior to accommodate drink tubes and an intercom system (sold separately) Snell SA2020 and FIA 8859-2015 approved The most effective helmet is one that fits properly. To measure your head, have an assistant use a dressmaker's tape or a piece of string to measure the circumference of your head. Start at a point about an inch above your eyebrows, looping around the back of your head at the point that results in the largest measurement, and finally around to the front again. It's a good idea to take two or three measurements to make sure you have the largest one. This helmet will ship with signature required for delivery.
Arai GP-5W Helmet SA2020
Arai Arai GP-5W Helmet SA2020 $849.95
Arai Auto Racing GP-5W SA2020 Helmet The Arai Auto Racing GP-5W SA2020 Helmet is perfect for stock car, sedan, and rally drivers. The GP-5W Helmet is a favorite because of its wider, 90mm (approx 3.5 top to bottom) eye port opening. The GP-5W uses its own exclusive shield with this larger opening. The GP-5W is Snell SA2020 certified with M6 washer/nuts installed at the factory. Drivers of any experience level will be able to easily install their Head and Neck Restraint system anchor posts (sold separately). The Arai Auto Racing GP-5W SA2020 also comes with the FIA-8859-2015 certification sticker found on the shell interior lining. SCLC CONSTRUCTION The GP-5W Helmet SA2020 is built with Arai's exclusive, very-lightweight SCLC (Super Complex Laminate Construction) shell technology. This ensures a low overall weight to balance the added weight of the helmet larger shield. SHELL SHAPE The The Arai Auto Racing GP-5W Helmet SA2020 helps reduce fatigue for the driver due to its more natural head shape, smaller shell size, and lower center of gravity to assist with balance and stability. INTERIOR FIT The The Arai Auto Racing GP-5W Helmet SA2020 is designed to closely match the shape of the human head, allowing for a snug, yet comfortable, fit. Arai has developed this natural shape over more than 50 years of helmet design research and refinement. WIDER EYE PORT Sedan drivers will appreciate the larger, 90mm eye port, top to bottom. A visor peak is available for drivers not needing a shield on the The Arai Auto Racing GP-5W Helmet SA2020. REMOVABLE/REPLACEABLE CHEEK PADS Low-maintenance, easy-to-clean cheek pads are removable, washable, and replaceable with pads of varying thickness to provide a snug, safe fit. M6 ANCHORS The FIA-8859-2015 certified GP-5W Helmet SA2020 is pre-installed with the M6 threaded washer/nut with 6mm threads. This convenient feature allows the driver to use the anchor system that works with their Head and Neck Restraints the best. The anchor post is made to rest flush on the helmet surface due to a flat surface area around the mounting nut. Accepts a variety of anchor systems for Head and Neck Restraints. VENTILATION Sedan car and closed cockpit drivers need greater airflow when racing. The upper ventilation system of the GP-5W SA2020 Helmet incorporates two exhaust vents and two large intake ducts to help keep the driver cool and comfortable. OPTIONS INCLUDE Anti- Fog Shields in Clear, Light Tint and Dark Smoke; Standard shields in Clear, Light Tint and Dark Smoke. An effective helmet is one that fits properly. Have an assistant use a measuring tape, or a piece of string to measure the circumference of your head starting at a point approximately one inch above the eyebrows in front, around a point in the back of the head that results in the largest possible measurement, and finally wrapping back to the front. It is a good idea to take several measurements to make sure you have the largest one. This helmet will ship to you with signature required for delivery.
Bell GT6 Pro Helmet SA2020
Bell Bell GT6 Pro Helmet SA2020 $799.95
Bell GT6 Pro Helmet SA2020 The GT6 Pro features the same modern and aggressive design as HP6, developed for racers in closed-car environments, featuring a wide eyeport for extended vision with an lightweight Premium carbon glass shell. Its ventilation slots can be connected to various types of air intakes for external cooling systems. It can be fitted with optional earcups providing optimal noise insulation, with fully integrated radio communication kit and hydration systems (available separately or in GT6 RD Titanium version). FEATURES Lightweight Premium Carbon Fiberglass Composite shell Wide eyeport opening for optimal vision in closed cockpit cars Advanced multi-density, multi-piece liner to maximize energy absorption and impact performance Integrated channels in face piece offering multiple options to install drinking tube, valves, and radio systems Extraction vents to maximize cooling and air circulation Factory installed Hans anchors as original equipment Optional top forced air intake can be installed on the left or right top side vents - available for use with and external cooling system Optional earcups for increased noise insulation Interior: Dark Grey High Strength High Comfort FR Fabric Color: Gloss White or Matte Black Homologation: FIA8859-2015 & Snell SA2020 Sizes: 6 3/4 (54) to 7 5/8+ (61+) IN THE BOX GT6 Pro Helmet Clear SE06 3mm DSAF Shield Installed Drawstring Helmet Bag Plastic Tearoff Posts Installed Hex Wrench Key
Bell GTX.3 Helmet SA2020
Bell Bell GTX.3 Helmet SA2020 $799.95
Bell GTX.3 SA2020 Helmet With its refined, aerodynamic style and lightweight carbon composite shell, the Bell Racing Helmets GTX.3 Composite SA2020 helmet provides the best performance and pro features for open wheel, open compartment, karting, formula and dirt track racers. This Bell GTX.3 Composite SA2020 has an integrated shield and dual screen anti-fog (DSAF) visor with rear-facing vents which are ideal for these forms of racing, allowing for air exchange and unobstructed vision without worrying about dust and dirt. FEATURES: Snell SA2020 and FIA 8859-2015 homologation. Includes clear SE03 3mm DSAF shield (SV SE03/05 pivot system) with DSAF anti-fog insert. Sleek aero styling with integrated wing. Front chinbar Gurney ("duckbill") improves high-speed aerodynamic performance. Venturi airflow system lets fresh air in, hollow synthetic rubber gasket seal keeps dirt, water and dust from getting inside. High-strength lightweight carbon-composite construction with new high-pressure molding system. Multi-piece, multi-density high-impact custom bead absorbing liner for low- and high-velocity impact protection. Ultra-plush grey Comfort-Max FR¬ interior fabric wicks away moisture. Install integrated drinking tube and radio microphone systems with the integrated face piece channels. Multi-density foam interior and contoured cheekpads offer a professional fit. Standard-sized eyeport. M6 terminal hardware and hex wrench for Head and Neck Restraint devices.  
Bell BR8 Helmet SA2020
Bell Bell BR8 Helmet SA2020 $699.95
Bell BR8 Helmet SA2020 Designed for off-road and dirt forms of racing, the versatile BR8 can be used in multiple configurations including standard, left or right side forced air, left or right 3/4 top forced air, or top forced air. Utilizing an innovative kit system (included with the helmet), racers can customize the BR8 to adapt to different forms of racing and seat configurations providing the ultimate flexibility in one model. The BR8 features an aerodynamic front duckbill, Double Screen Anti-Fog (DSAF) insert to create a positive visor seal and prevent shield fogging, and rear-facing Venturi airflow vents that prevent dust from entering the helmet while still allowing forced air to be introduced into the helmet. The BR8 features a unique air chamber system that evenly distributes airflow around the head regardless of the top air configuration used. The helmet can be used with or without ear cups. HELMET COLORS: Gloss White Matte Black FEATURES: Lightweight composite shell Advanced multi-density, multi-piece liner to maximize energy absorption and impact performance Integrated channels in face piece offer multiple options to install drink tube and radio system Includes front duckbill to enhance aerodynamic performance Comes standard with rear facing vents that create a Venturi effect allowing air to exchange and circulate in the helmet white preventing dust and dirt from entering Can be converted to left or right side air, 3 4 left or right top air, or top air by using a versatile kit system (included) with forced air nozzle and cover plates Forced air kits available for aftermarket including quick lock (V10) and are fully compatible with Maglock Can be used with or without ear cups (ear cups included) M6 terminals for FHR anchor attachment and homologated for use with approved head and neck devices Interior: Black High Strength High Comfort FR Fabric Color: Gloss White and Matte Black Homologation: Snell SA2020
Bell GP3 Sport Helmet SA2020
Bell Bell GP3 Sport Helmet SA2020 $699.95
Bell GP3 Sport SA2020 Helmet The Bell GP3 combines traditional Formula 1 styling, a versatile air intake system, a Double Screen Anti-Fog (DSAF) visor shield, and a lightweight carbon composite shell with leading-edge aerodynamic performance. A great option for open-wheel racers and karters who demand professional features, performance and comfort, the GP3 Sport gives you maximum ventilation and a clear view even in the toughest track conditions. FEATURES: Lightweight composite shell Homologations: Snell SA2020 and FIA 8859-2015 approved Advanced multi-density, multi-piece liner to maximize energy absorption and impact performance Optical grade injection molded Double Screen Anti-Fog (DSAF) visor Versatile ventilation system featuring lower front chin bar ventilation and upper manual lever air intake Vents can be open or closed Front duckbill (chin spoiler) for improved aerodynamic performance Compatible with Bell rear spoilers, top gurney, and chin bar gurneys (available separately) for enhanced stability at high speeds Integrated channels in face piece offer multiple options to install drink tube and radio system M6 terminals for FHR anchor attachment, homologated for use with approved head and neck devices Synthetic rubber gasket seal to prevent dirt and water entering the helmet Shield and pivot kit: SE03, SV(SE03/SE05) Colors: White or Matte Black Sizes: S, M, L, XL  
Bell K1 Pro Helmet SA2020
Bell Bell K1 Pro Helmet SA2020 from $559.95
Bell K1 Pro Helmet SA2020 The Bell Racing Helmets K1 Pro composite auto racing helmet is a multi-use, full-featured helmet with superior ventilation, aero styling and Bell's aggressive chin bar design and front chin Gurney (duckbill). The K1 Pro is a great helmet for open wheel racers, closed car racers and kart racers who demand superior features including light weight, excellent fit, and multiple ventilation options. The Bell Racing Helmets K1 Pro can be used in an open wheel configuration with air intake (included), or in a closed car configuration with the top forced air insert (sold separately). HELMET COLORS: Gloss White Matte Black Circuit Blue Circuit Red FEATURES: Snell SA2020 homologation. All sizes are in centimeters. All-purpose, versatile helmet. Aggressive Bell aero styling. Lightweight composite shell. Multi-piece, multi-density high-impact custom bead absorbing liner for low- and high-velocity impact protection. Integrated channels in the face piece for integrated radio mic systems. Black Comfort Plus FR interior fabric for durable performance. Multi-density foam interior padding for superior fit. Excellent ventilation system includes direct-flow upper and lower chin bar vents, 10 intake and extraction vents, and a clear 2mm air intake vent. Top forced-air option available (sold separately). Hollow synthetic rubber gasket seal ensuring no air, water or dirt leaks into the helmet. Standard-size eyeport. 287 3mm SRV clear shield (SRV-1 pivot system). M6 terminal hardware and hex wrench for Head and Neck Restraint devices
HJC H70 Top Air Helmet SA2020
HJC HJC H70 Top Air Helmet SA2020 $549.99
HJC H70 Top Air Auto Racing Helmet Whether you're navigating the sand dunes of Baja or on the bank turns of the Nurburgring, HJC Motorsports has you covered with the release of its most versatile helmet to date: the all-new H70. Designed with a straightforward approach, the H70 is at home in nearly any driving conditions with the help of a few key attachments already in the box: a rear spoiler for open-cockpit driving and a top forced-air kit for vehicles outfitted with filtered air systems. Complete with factory installed M6 terminals for your favorite head and neck restraint, the HJC H70 will have you ready to take on your favorite race track anywhere in the world. FEATURES: Snell SA2020 and FIA 8859-2015 approved Advanced Fiberglass Composite Shell (with two shell sizes, XS-M and L-XXL) Advanced Air Circulation System: two front intakes and eight top vents Fire resistant moisture-wicking removable and washable cheek pads and head liner Polycarbonate anti-fog shield with tear-off posts Double D-ring retention system Pre-installed M6 terminals for head and neck restraints Optional shields available: Amber, Dark Smoke, Dark Blue, Fire Red, and Black Chrome Sizes: XS - XXL INCLUDED ACCESSORIES: Vent Plugs (8 pcs) Lower Vent Cover Top Forced Air Rear Spoiler