599 GTB

CMS RF1 DOT4 Racing Brake Fluid HIGH BOILING POINT WITHOUT THE HIGH PRICE RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid. RF1 RACING BRAKE FLUID DETAILS Typical dry boiling point: 328º C (622º F) Typical wet boiling point: 204º C (399º F) Exceeds DOT3 & DOT4 standards Bottle size: 500 ml (16.9 fl oz) Click Here for Product MSDS Sheet A WORD ABOUT FLUSHING RACING BRAKE FLUID All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Girodisc Brake Pad Spreader GDPS01 This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The Girodisc Brake Pad Spreader is designed to easily spread brake pads and pistons to facilitate quick replacement of pads and/or rotors in a shop or racing environment. No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons fully and evenly into their bores with one squeeze of the levers. The Girodisc Brake Pad Spreader was designed to be used with popular racing brake calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help it fit into any caliper, the amount of throw is adjustable. Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers. The Girodisc Brake Pad Spreader is made from heavy-gauge steel, powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Brake Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors frequently.

Pagid Racing Brake Pad Shape No. 4906 Fits the Following Vehicles: Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 15 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 09 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 15 - X Dodge Viper ACR [ceramic brakes] 14 - 17 X Ferrari 360 Challenge Stradale [ceramic brakes] 03 - 05 X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 07 - 10 X Ferrari 458 Italia [ceramic brakes] 10 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 16 - X Ferrari 599 GTB Fiorano 06 - 12 X Ferrari Enzo [ceramic brakes] 02 - 04 X Ferrari F430 [ceramic brakes] 05 - 10 X Ferrari Several ceramic brakes CCM X Lamborghini Aventador LP700-4 [ceramic brakes] 11 - X Lamborghini Several ceramic brakes X Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. These Pagid Racing Brake compounds are for ceramic rotors only. Pagid RSC 1 Compound (Ceramic Rotors Only) A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSC 2 Compound (Ceramic Rotors Only) Pagid RSC 2 is a special race compound for ceramic discs with a high content of fibers in the friction surface for sprint and endurance circuit racing. RSC 2 is a low metallic resin bonded material containing steel and aramid fibers. This material is specifically developed for above mentioned applications.

Pagid Racing Brake Pad Shape No. 8091 Fits the Following Vehicles: Make Model Build (Year) Front Rear Chevrolet Camaro Z28 [Gen 5] [ceramic brakes] 2015 - 17 X Chevrolet Corvette C6 Brembo [ceramic brakes] 2009 - 13 X Chevrolet Corvette C6 Brembo [6-piston iron rotors] 2009 - 13 X Chevrolet Corvette C7 Z06 [ceramic brakes] 2015 + X Ferrari 430 Challenge [ceramic brakes] X Ferrari 430 Scuderia [ceramic brakes] 2007 - 10 X Ferrari 458 Italia [ceramic brakes] 2010 - 15 X Ferrari 488 Challenge race car [ceramic brakes] 2016 + X Ferrari 599 GTB Fiorano [iron rotors] 2006 - 12 X Ferrari Several ceramic (CCM) brakes X McLaren 570S [ceramic brakes] 2015 + X McLaren 650S / Spyder [ceramic brakes] 2014 - 17 X McLaren 675LT [ceramic brakes] 2015 + X McLaren MP4-12C [ceramic brakes] 2011 - 14 X Fits the Following Calipers: Make Type Remarks Shape No. Brembo XA5.71.xx 6-piston D85 16mm 8091 Pagid Racing Brake Pads are engineered for high-performance driving, delivering exceptional stopping power, durability, and control under the most demanding conditions. Trusted by professional racers and performance enthusiasts worldwide, these pads are crafted using advanced friction materials and cutting-edge technology to ensure consistent performance, low fade, and excellent modulation. Whether you're on the track or tackling aggressive street driving, Pagid Racing Brake Pads provide the reliability and confidence you need to push your vehicle to its limits. Pagid Racing Brake compounds are for steel (cast iron) rotors only unless otherwise noted. Pagid RSL 1 Compound: Used in GT cars, touring cars and prototype endurance racing. Due to the high friction and good modulation, often used in sprint races as well. RSL 1 is a low metallic resin bonded material containing steel and aramid fibers with very high heat resistance. It maintains a constant friction level over a wide range of temperatures. Its reduced wear rate and disc friendliness make this material appropriate for endurance races. In the 8091 pad shape, the RSL 1 comes in an RSL 1 Special compound, both specified for Brembo and Ford Multimatic applications. Pagid RSL 19 Compound: Pagid RSL 19 is a low metallic resin bonded material containing steel and aramid fibers. It maintains a constant friction level across a broad range of temperatures. The material features very good modulation and release characteristics. Rear axle usage in combination with RSL 1 or RSL 2 on the front axle in heavier cars (GT3/GTE). Front axle usage for lighter GT and touring cars. Pagid RSC 1 Compound (Ceramic Rotors Only): A race and track day compound for all known types of ceramic brake discs, RSC 1 is a low metallic resin bonded material containing steel and aramid fibers. This material features good all-round characteristics and is suitable for all types of usage. Pagid RSC 2 Compound (Ceramic Rotors Only): Pagid RSC 2 is a special race compound for ceramic discs with a high content of fibers in the friction surface for sprint and endurance circuit racing. RSC 2 is a low metallic resin bonded material containing steel and aramid fibers. This material is specifically developed for above mentioned applications. Pagid RSC 3 Compound (Ceramic Rotors Only): RSC 3 is a low metallic resin bonded material containing steel fibers. This material is specifically developed for above mentioned applications. It is a special race compound for ceramic discs with low content of fibers in the friction surface for sprint and endurance circuit racing.

A2-075 Girodisc 2pc Rear Brake Rotors Fits Ferrari 599 GTB The Girodisc system is a direct replacement for the OE disc.No modifications are necessary. The disc will bolt directly to the car and work with OE calipers perfectly. The central hat section of our rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum.  The disc is made from our own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc.  The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 8 or 10 high strength alloy steel drive pins, manufactured by Girodisc in the USA to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The pins are secured by grade 12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor when needed.  Features: • Built for racing reliability and consistent performance • Compatible with demanding track environments • Designed for perfect fit and easy installation FAQs: Is this part track-proven? Yes, it has been tested extensively under racing conditions. Does it require professional installation? While not required, professional installation is recommended for best performance. Will this fit my vehicle? Please refer to the fitment guide or contact us to confirm compatibility. Can I return this if it doesn’t fit? Yes, as long as it’s unused and in original packaging.

A1-075 Girodisc 2pc Front Brake Rotors FITMENT: Ferrari 599 GTB with CCM rotors is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most products the same or the next business day to ensure we meet your delivery deadline. The Girodisc system is a direct replacement for the OE disc however a different brake pad with an annulus (pad swept area) of 66mm or less must be used. This is done to keep the rotor weight at a reasonable level. If we manufactured a rotor with the same annulus as the OEM CCM rotors they would be far too heavy. The necessary pad shape is available from both Pagid and PFC. If there is a specific pad compound you're after, please contact us directly and we'll provide the correct part numbers. The central hat section of our rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc. The rotor and hat have a floating mount system, which utilizes 8 or 10 high-strength alloy steel drive pins, manufactured by Girodisc in the USA to their own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking while maintaining axial and radial float between the hat and disc. The pins are secured by Grade-12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side, allowing the rotor to grow with heat expansion while eliminating the rattle and noise typically associated with floating rotors. This float also allows the rotor to self-center between the brake pads. Once the Girodisc system is in place, simply replace the cast iron rotor when needed. Sold/priced in pairs. Features: • Built for racing reliability and consistent performance • Compatible with demanding track environments • Designed for perfect fit and easy installation FAQs: Is this part track-proven? Yes, it has been tested extensively under racing conditions. Does it require professional installation? While not required, professional installation is recommended for best performance. Will this fit my vehicle? Please refer to the fitment guide or contact us to confirm compatibility. Can I return this if it doesn’t fit? Yes, as long as it’s unused and in original packaging.