991 Carrera S/4S/GTS

A1-122 Girodisc 2pc Front Brake Rotors (350mm) FITMENT: Porsche Carrera S 991.2 Porsche Carrera 4S 991.2 Porsche Carrera GTS 991.2 This Girodisc system is a direct replacement for OEM Porsche steel (cast iron) rotors1 with the use of the provided caliper spacers. The Girodisc rotors are slightly larger than the stock Porsche rotors at 350mm vs. 340mm, providing greater braking force and cooling capacity. The Girodisc front rotors are approximately 21.0 lbs. vs. 24.4 lbs. for the stock units. This reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement as well, minimizing future replacement costs and delivering outstanding performance. Sold/priced per pair. 1 Note: this Girodisc kit does not fit Porsche models with factory PCCB brakes.

The Girodisc system is an upgrade to a 350mm two-piece steel rotor and aluminum hat combination, a direct replacement for the OEM brake disc. The two-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements -- as opposed to a big brake kit -- your factory brake bias is maintained as well as your ABS efficiency. Girodisc rotors are lighter than the OEM rotors, reducing rotational and unsprung weight for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads and RF1 racing brake fluid (also available from ), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured in the USA from cast iron, made to the same specification and with the same material used by professional racing organizations. The rotor's curved-vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from braking while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise typically associated with floating rotors. The two-piece Girodisc design allows for rotor-ring only replacement to minimize future replacement costs. Priced per pair

A2-032 Girodisc 2pc REAR Brake Rotors (OEM PCCB) The Girodisc system is an upgrade to a 350mm two-piece steel rotor and aluminum hat combination, a direct replacement for the OEM PCCB brake discs. The two-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance iron replacements, you can eliminate the risk of cracking or breaking your expensive PCCB rotors at the race track. When used with Pagid or PFC performance brake pads and RF1 racing brake fluid (also available from ), you have an amazing solution to overheating, cracking rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured in the USA from cast iron, made to the same specification and with the same material used by professional racing organizations. The rotor's curved-vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from braking while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise typically associated with floating rotors. The two-piece Girodisc design allows for rotor-ring only replacement to minimize future replacement costs. Priced per pair Features: • Built for racing reliability and consistent performance • Compatible with demanding track environments • Designed for perfect fit and easy installation FAQs: Is this part track-proven? Yes, it has been tested extensively under racing conditions. Does it require professional installation? While not required, professional installation is recommended for best performance. Will this fit my vehicle? Please refer to the fitment guide or contact us to confirm compatibility. Can I return this if it doesn’t fit? Yes, as long as it’s unused and in original packaging.

D1-122 GiroDisc Replacement Rotors REPLACEMENT ROTOR RINGS ONLY. INCLUDES NEW INSTALLATION HARDWARE. DOES NOT INCLUDE ALUMINUM HATS. is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. These Girodisc replacement rotor rings are direct replacements for the iron discs on your Girodisc two-piece rotors, and no modifications are necessary. New cap screws and washers are included with these replacement rotors. We do not recommend re-using the old hardware. These rings will not work with factory center hats. They are designed to work with Girodisc hats only. The replacement rotor rings and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor ring-only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

ROTOR RINGS ONLY (NO HATS) Need new rings for your Girodisc A2-032 rear rotors? We got them. Rings come complete with all new hardware and full instructions for re-assembly. Price is for a pair of rings and 2 hardware kits. Additional hardware kits are available separately upon request.

PFC 08 COMPOUND One of PFC's most popular compounds which came to fame in Endurance Sports Car and GT racing due to its performance in applications where smooth initial bite is a must. PFC 08 has a slight friction rise with temperature, excellent release and modulation characteristics. Despite its considerable performance, PFC 08 has the lowest wear rate of all PFC compounds and can easily match the wear characteristics of competitors' endurance materials, but with much higher bite and consistent performance across a broad temperature range.

Castrol SRF Racing Brake Fluid With 518º F Wet Boiling Point Castrol React SRF is a very high-performance brake fluid specifically developed for motorsports applications where extreme braking conditions are encountered. Castrol SRF has an exceptionally high wet boiling point of 518° F (256º C) along with a very respectable 590° F dry boiling point. Both exceed DOT 4 specifications. Castrol SRF Brake Fluid's unique silicon ester technology absorbs less water than conventional glycol ether fluids and prevents the fluid's high-temperature performance from deteriorating. Its wet boiling point of 518° F is vastly superior to the minimum requirement demanded by the current US DOT 4 specification. Its ability to withstand temperatures in excess of 590° F and superior resistance to the effects of absorbed water have established Castrol SRF Brake Fluid as the world's premier fluid for the hydraulic brakes used in all forms of motorsport and racing. Castrol SRF brake fluid can make a critical difference when using metallic brake pads with high thermal conductivity. Resistance to foaming makes it an excellent choice for use with ABS braking systems. Castrol React SRF Racing Brake Fluid is now packaged in easy-pour 1 liter plastic bottles. Castrol React SRF Racing Brake Fluid Details Manufacturer: Castrol Manufacturer part number: 12512 UPC: 079191005125 Size: 1 liter Service life: 18 months DOT Rating: DOT 4 Dry Boiling Point: 590° F (296º C) Wet Boiling Point: 518° F (256º C) Compatible with other DOT3/DOT4: Yes Size: 1 liter (33.8 fl. oz.) plastic bottles Development of Castrol React SRF Racing Brake Fluid Castrol React SRF evolved as a direct result of Castrol's ongoing Research and Development program for brake fluids which identified this silicon ester technology as providing considerable performance benefits when compared with conventional glycol ether borate ester fluids.Following exhaustive laboratory tests at Castrol's International Technology Centre in the UK, the final formulation for Castrol SRF was subjected to an extensive road-test program on the Gross Glockner and Stelvio passes high in the Austrian and Italian Alps. It then underwent an independent track test program conducted by a famous Formula One racing team. Their assessment was that "Castrol SRF is the best racing brake fluid we have ever used." Subsequently, Castrol SRF was offered to top-flight racing and rally teams throughout the world including most of the Formula One team, the all-conquering Jaguar and Mercedes -Benz sports car teams, and the Audi, Nissan, and Toyota rally teams. Enthusiastic recommendation by these experts soon created immense interest in Castrol SRF throughout the whole spectrum of national and international motorsport. Today, Castrol React SRF is regarded by the international motorsport community as being without equal and it is chosen not only by factory-supported teams but by private competitors throughout the world. The Solution To High-Temperature Vapor Lock All conventional brake fluids used in cars and motorcycles are hygroscopic, that is, they absorb water from their surroundings. Strange though it may seem, the flexible hoses incorporated in braking systems are permeable to water and in time enough, water can find its way into the system via the hoses and seriously affect the brake fluid's performance. This water reduces the boiling point of the fluid (i.e., it lowers the temperature at which gas bubbles begin to form). When these bubbles form, they turn a virtually incompressible liquid into a mixture of gas and liquid which can be compressed quite considerably, thus severely reducing the efficiency of the brakes. In this situation, a driver finds that the brakes feel spongy. Brake-pedal travel will increase and it may be necessary to 'pump' the pedal to get the brakes to function effectively. However, when the brake fluid reaches a temperature at which the water in the fluid causes gas to be produced, which is equal to the volume swept by the piston in the master-cylinder, vapor-lock occurs and the brakes become inoperative. When this happens, the first indication the driver has that something is wrong is when he applies the brakes. The pedal goes down to the floor and the car carries on at undiminished, possibly fatal speed.The silicon ester technology in Castrol React SRF addresses this problem in two ways. Firstly, Castrol SRF is less hygroscopic than conventional brake fluids - it absorbs less water in a given time. Secondly, unlike conventional glycol ether fluids, Castrol SRF reacts chemically with the absorbed water to reduce its adverse effects, thus preventing the fluid's high-temperature performance and safety margins from deteriorating as rapidly as they would otherwise do.Castrol React SRF exceeds the US Federal Standards FMVSS 116 DOT 3 and DOT 4, ISO 4925, JIS K2233, and current SAE J1703 and is miscible with all conventional brake fluids conforming to these standards. However, mixing Castrol React SRF and conventional brake fluids will reduce the benefits of Castrol React SRF. It is strongly recommended that conventional brake fluid be drained from the system before flushing and refilling with Castrol React SRF.

The World's Most Advanced Racing Brake Fluid Imagine you're on the race track, hitting the entry to a corner. Your foot hammers down on the brake, and you feel... absolute perfection. That's Halo P1 for you. Developed with Fade Resistant Technology, this specialist brake fluid is the secret sauce for top-tier motorsport enthusiasts worldwide. Why? Because when you're tearing up the track, the last thing you want is a mushy pedal feel. Halo P1 delivers a low and stable compressibility profile over an extended temperature range, not to mention a crazy-high dry boiling point of 341º C (646º F). All of this is to ensure your brake pedal feel remains as strong and consistent as your lap times. Halo P1 Brake Fluid Features & Benefits That'll Make You Weep Tears of Joy Fade Resistant Technology: Keeps your pedal feel consistent, lap after lap, so you can focus on nailing those corners. Pure Methyl Borate Ester Base: The purity level here is so high, it's like the distilled essence of speed itself, ensuring extreme resistance to compression, even when things get hot (and we mean really hot). World-Beating Dry Boiling Point: At 341° C (646° F), it's like this fluid laughed in the face of boiling points and set a new standard. Low Viscosity & High Lubricity: Because your brake system deserves to be as smooth as your driving skills. What Makes Halo P1 Brake FLuid The Secret Weapon? While other brake fluids are off playing checkers, Halo P1 is mastering chess. It's not just another methyl glycol borate ester brake fluid; it's a revolution in braking performance. With its unique proprietary manufacturing process, it achieves the highest levels of purity and the lowest compressibility possible, remaining constant over a wide temperature range. This is the highest boiling point of any racing brake fluid on the market, folks. And the lubricity? Off the charts, especially at high temperatures. Halo P1 Brake FLuid FAQs That'll Clear the Air Before you rush off to convert your entire garage to a Halo P1 shrine, let's tackle some of those burning questions you might have: Can I use Halo P1 in my daily driver? As much as we love the enthusiasm, Halo P1 is a race-only formula. It's like putting a rocket booster on a bicycle – thrilling, but not recommended. How often should I change my brake fluid with Halo P1? Regular maintenance is key in racing. Check with your team or mechanic, but before every major race is a good rule of thumb. The Call to Action You've Been Waiting For So, are you ready to elevate your racing game to legendary status? To feel the rush of confidence as you brake later and harder, knowing your brake fluid won't let you down? It's time to switch to Halo P1. Your podium awaits.