997 Turbo

CMS RF1 DOT4 Racing Brake Fluid Real-Life High Boiling Point Without The Real High Price RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid. RF1 Racing Brake Fluid Details Typical dry boiling point: 328º C (622º F) Typical wet boiling point: 204º C (399º F) Exceeds DOT3 & DOT4 standards Bottle size: 500 ml (16.9 fl oz) Click Here for Product MSDS Sheet A Word About Flushing Brake Fluid All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.

Girodisc Porsche 991 GT3 non-PCCB Replacement Front Rotor Rings Genuine Girodisc replacement rotor rings for your Porsche 991 GT3 and 981 Cayman GT4 non-PCCB front brakes. The GiroDisc D1-066 is the direct replacement and part of your Girodisc A1-146 brake kit. This complete kit includes two new slotted, vented perfect fit rotor rings and two new hardware kits. Does not fit stock Porsche hats. Girodisc Porsche 991 GT3 non-PCCB Replacement Rotor Rings Details: Manufacturer: GiroDisc Manufacturer Part Number: D1-066 Replacement for Girodisc kit: A1-146 Surface: Slotted Material: Steel Intended for Street/Track Use: Yes For Use with Stock Calipers: Yes Rotor Construction: Vented Rotor Style: Slotted surface Rotor Material: Iron Rotor Finish: Black E-coat Quantity: One pair (one axle set) GiroDisc Floating Rotor Ring: Quality hi-carbon cast iron is the foundation of every GiroDisc brake rotor. Every rotor ring is made carefully in house at the GiroDisc factory in Washington state. The GiroDisc rotor utilizes a curved vane design that was originally developed in racing to act as a centrifugal air pump to force cooling air from the center of the rotor ring to the outside. This principle is similar to what is know as a squirrel cage fan design. By having impellers (vanes) between the two rotor faces,  the air is moved radially, from the center outward, changing the direction of the airflow and increasing velocity. This design is mechanically strong, reliable very effective. GiroDisc Rotor Ring Hardware: The GiroDisc rotor ring and light-weight aluminum hat have a floating mount system, which utilizes 8 or 10 high strength alloy steel drive pins, manufactured by Girodisc in the USA to our own specifications and cadmium plated for a long lasting corrosion resistance. These drive pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The drive pins are secured by grade 12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads. GiroDisc Rotor Ring Replacement: Once the Girodisc system is in place, simply replace the cast iron rotor when needed. Your GiroDisc replacement rotor rings come complete with 2 new rotor rings and all required floating rotor hardware. This is a very simple task that is quite fun. The aluminum rotor hat usually does not ever need replacement unless bent or damaged. If your damage has reached your GiroDisc hat, you almost certainly have quite a number of other things to replace also. The hat is rugged and overly strong.  Girodisc Porsche 991 GT3 non-PCCB Replacement Rotor Rings Fitment: Girodisc A1-146 brake kit

  Fits These Vehicles: Make Model Build (Year) Front Rear Porsche 996 GT2 02 - 05 X   Porsche 996 GT3 02 - 05 X   Porsche 996 GT3 Cup 02 - 05 X   Porsche 996 GT3 RS [street car] 03 - 05 X   Porsche 997 all models ceramic brakes 05 - 12 X   Porsche 997 GT3 07 - 11 X   Porsche 997 GT3 RS 07 - 12 X   Porsche 997 Turbo 06 - 12 X   Porsche Boxster [987] [ceramic brakes] 05 - 12 X   Porsche Carrera GT 04 - 06 X X Porsche Cayman [987] [ceramic brakes] 06 - 12 X   COMPOUNDS: RSL29, RSC1   RSL 29: The Pagid RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.

This Girodisc system is a 380mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the one-piece OEM GT4 steel brakes. The A1-166 will bolt directly to the GT4 and work perfectly with your OEM calipers. There are two main reasons for replacing your OEM rotors: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the slotted Girodisc A1166 will far outlast the OEM drilled rotors. When subjected to intense heat in a racing or track-day environment, the drilled holes in the OEM rotors originate cracks which can lead to rotor failure. When paired with the Girodisc A2-155 rear rotors, your factory brake bias and ABS efficiency are maintained. When used with Pagid or PFC performance brake pads, and Discovery Parts RF1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes eight to ten high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

The Girodisc system is an upgrade to a 350mm two-piece steel rotor and aluminum hat combination, a direct replacement for the OEM brake disc. The two-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements -- as opposed to a big brake kit -- your factory brake bias is maintained as well as your ABS efficiency. Girodisc rotors are lighter than the OEM rotors, reducing rotational and unsprung weight for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads and Discovery Parts RF1 racing brake fluid (also available from Discovery Parts), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured in the USA from cast iron, made to the same specification and with the same material used by professional racing organizations. The rotor's curved-vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from braking while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise typically associated with floating rotors. The two-piece Girodisc design allows for rotor-ring only replacement to minimize future replacement costs. Priced per pair

RT RE10*:RE10 is the ultimate endurance race compound offering a balance of excellent stopping power, low thermal conductivity, extremely low pad and disc wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms *Denotes a "race only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges so it is important to choose the desired compound for the correct environment the vehicle will be used in. Pad Compounds are run on a brake dynamometer over multiple brake applications (stops) to test the materials in a controlled environment for the most accurate data. Wear rates and temperatures can be influenced by car setup, grip levels, track layout/configuration and many other variables.

RT RE10*:RE10 is the ultimate endurance race compound offering a balance of excellent stopping power, low thermal conductivity, extremely low pad and disc wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms *Denotes a "race only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges so it is important to choose the desired compound for the correct environment the vehicle will be used in. Pad Compounds are run on a brake dynamometer over multiple brake applications (stops) to test the materials in a controlled environment for the most accurate data. Wear rates and temperatures can be influenced by car setup, grip levels, track layout/configuration and many other variables.

Fits These Vehicles Make Model Build (Year) Front Rear Porsche 997 3.6 C & 3.6 C4 08 - 11   X Porsche 997 all models ceramic brakes 05 - 12   X Porsche 997 GT3 07 - 11   X Porsche 997 GT3 Cup [19 mm thick pads] 05 - 12   X Porsche 997 GT3 Rally 05 - 12   X Porsche 997 GT3 RS 07 - 12   X Porsche 997 Turbo 06 - 12   X   RSL 29: The PAGID RSL29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface. RST 3: The PAGID RST3 is a medium-high friction metal-ceramic compound containing steel and acrylic fibers. It has very low heat conductivity, good initial bite, and excellent modulation and release characteristics. Optimized for rally on tarmac and gravel, GT and Touring cars, and club racing.

ROTOR RINGS ONLY (NO HATS) Need new rings for your Girodisc 350mm 2pc rotors? We got them. Rings come complete with all new hardware and full instructions for re-assembly. Price is for a pair of rings and 2 hardware kits. Additional hardware kits are available separately upon request.

Discovery Parts is an authorized dealer for Girodisc products. As one of the largest dealers in the US, we ship most products same or next business day to ensure we meet your delivery deadline. The Girodisc system is an upgrade to a 350mm two-piece steel rotor and aluminum hat combination, a direct replacement for the OEM brake disc. The two-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements -- as opposed to a big brake kit -- your factory brake bias is maintained as well as your ABS efficiency. Girodisc rotors are lighter than the OEM rotors, reducing rotational and unsprung weight for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads and Discovery Parts RF1 racing brake fluid (also available from Discovery Parts), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured in the USA from cast iron, made to the same specification and with the same material used by professional racing organizations. The rotor's curved-vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from braking while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise typically associated with floating rotors. The two-piece Girodisc design allows for rotor-ring only replacement to minimize future replacement costs. Priced per pair

PFC 08 COMPOUND One of PFC's most popular compounds which came to fame in Endurance Sports Car and GT racing due to its performance in applications where smooth initial bite is a must. PFC 08 has a slight friction rise with temperature, excellent release and modulation characteristics. Despite its considerable performance, PFC 08 has the lowest wear rate of all PFC compounds and can easily match the wear characteristics of competitors' materials but with much higher bite and more consistent performance across a broad temperature range. FITMENT (Iron Rotors Only): Porsche 997.1 & 997.2 GT3/GT3RS Porsche 997 Turbo Porsche 996 GT3

PFC 11 COMPOUND A new generation sprint and medium distance friction material, giving you the ultimate in control with superior disc conditioning. Developed from PFC 01 compound with improved bite, modulation, and release characteristics. It is ultra smooth and developed to reduce wheel locking at the end of a stop while giving more cold and hot bite than the endurance oriented PFC 08 compound. Brake with confidence, with the ultimate control and modulation.

ROTOR RINGS ONLY (NO HATS) Need new rings for your Girodisc A2-032 rear rotors? We got them. Rings come complete with all new hardware and full instructions for re-assembly. Price is for a pair of rings and 2 hardware kits. Additional hardware kits are available separately upon request.

PFC 11 COMPOUND A new generation sprint and medium-distance friction compound, giving you the ultimate in control with superior disc conditioning. Developed from the PFC 01 compound with improved bite, modulation, and release characteristics. It is ultra smooth, developed to reduce wheel locking at the end of a stop while giving more cold and hot bite than the endurance oriented PFC 08 compound. PFC 08 COMPOUND One of PFC's most popular compounds which came to fame in Endurance Sports Car and GT racing due to its performance in applications where smooth initial bite is a must. PFC 08 has a slight friction rise with temperature, excellent release and modulation characteristics. Despite its considerable performance, PFC 08 has the lowest wear rate of all PFC compounds and can easily match the wear characteristics of competitors' materials but with much higher bite and consistent performance across a broad temperature range.  PFC 332 COMPOUND 332 has been formulated with lower bite and torque for rear applications.With smooth release, the 332 offers excellent stability and control.The 332 has been designed to work with ABS applications, and has exceptionally low wear rates  FITMENT (Iron Rotors Only) 997 & 997.2 GT3/GT3RS 997 & 997.2 Turbo 996 GT3