sale
CMS RF1 DOT4 Racing Brake Fluid (500 ml)
00
DAYS
00
HRS
00
MIN
00
SEC
Competition Motorsport CMS RF1 DOT4 Racing Brake Fluid (500 ml) from $21.95 $131.70
Buy 6+, Save $1 per bottle Buy 12+, Save $2 per bottle REDESIGNED BOTTLE, SAME TOP-OF-THE-LINE BRAKE FLUID Competition Motorsport RF1 fully synthetic Racing Brake Fluid is formulated to provide the highest, most reliable performance under racing and track-day conditions, where braking systems operate at very high sustained temperatures. RF1 exceeds all DOT 3 & 4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) There is perhaps no single safety system more important in racing than brakes. And no single part of that system is more critical than brake fluid. At Competition Motorsport, we got tired of (and a little nervous) using "racing" brake fluid on the track that didn't live up to its claimed performance when things got heated. So we did something about it. Manufactured in partnership with the brake fluid supplier to many teams in Formula 1, WEC, and many other professional series, RF1 Racing Brake Fluid is formulated to maintain consistent viscosity, lubricity, and compressibility at extreme temperatures and line pressures found in racing, track days, and spirited driving. Bottom line: you can spend more money, but you can't buy higher-performing racing brake fluid! SPECIFICATIONS: Typical dry boiling point: 622 F (328 C) Typical wet boiling point: 399 F (204 C) Exceeds DOT3 & DOT4 standards Individual 500 ml (16.7 oz.) bottles Click Here for Product MSDS Sheet All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!
Girodisc Pad Spreader GDPS01
Girodisc Girodisc Pad Spreader GDPS01 $250.00
Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.
D2-232 Girodisc Rear Rotor Rings
Girodisc D2-232 Girodisc Rear Rotor Rings $800.00
REPLACEMENT ROTOR RINGS ONLY. INCLUDES NEW INSTALLATION HARDWARE. DOES NOT INCLUDE ALUMINUM HATS. Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. These Girodisc replacement rotor rings for the Nissan R35 GT-R are Girodisc's updated variant. If you're not sure these are correct for your Girodisc rotors, please contact us. They the are direct replacements for the iron discs on your Girodisc two-piece rotors, and no modifications are necessary. New cap screws and washers are included with these replacement rotors. We do not recommend re-using the old hardware. These rings will not work with factory center hats. They are designed to work with Girodisc hats only. The replacement rotor rings and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor ring-only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.
D1-232 Girodisc Front Rotor Rings (390mm)
Girodisc D1-232 Girodisc Front Rotor Rings (390mm) $800.00
REPLACEMENT ROTOR RINGS ONLY. INCLUDES NEW INSTALLATION HARDWARE. DOES NOT INCLUDE ALUMINUM HATS. Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. These 390mm Girodisc replacement rotor rings are direct replacements for the iron discs on your Girodisc two-piece rotors, and no modifications are necessary. New cap screws and washers are included with these replacement rotors. We do not recommend re-using the old hardware. These rings will not work with factory center hats. They are designed to work with Girodisc hats only. The replacement rotor rings and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor ring-only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.
D1-249 Girodisc Front Rotor Rings (380mm)
Girodisc D1-249 Girodisc Front Rotor Rings (380mm) $800.00
REPLACEMENT ROTOR RINGS ONLY. INCLUDES NEW INSTALLATION HARDWARE. DOES NOT INCLUDE ALUMINUM HATS. Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. These 380mm Girodisc replacement rotor rings are direct replacements for the iron discs on your Girodisc two-piece rotors, and no modifications are necessary. New cap screws and washers are included with these replacement rotors. We do not recommend re-using the old hardware. These rings will not work with factory center hats. They are designed to work with Girodisc hats only. The replacement rotor rings and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor ring-only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.
A2-232 Girodisc 2pc Rear Brake Rotors (all R35)
Girodisc A2-232 Girodisc 2pc Rear Brake Rotors (all R35) $1,400.00
Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Nissan GT-R (R35, 2007+) The Girodisc system is a direct replacement for the OE disc. No modifications are necessary. The disc will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. These Girodisc rear rotors are approx 18.8 lbs. This reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair
A1-232 Girodisc 2pc Front Brake Rotors (DBA 390mm)
Girodisc A1-232 Girodisc 2pc Front Brake Rotors (DBA 390mm) $1,500.00
Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Nissan GT-R (DBA) 2012+ w/ 390mm stock rotors The Girodisc system is a direct replacement for the OE disc, they will bolt directly to the car and work with OE calipers perfectly. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair
A1-249 Girodisc 2pc Front Brake Rotors (CBA 380mm)
Girodisc A1-249 Girodisc 2pc Front Brake Rotors (CBA 380mm) $1,500.00
Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Nissan GT-R (CBA) 2007-2011 w/ 380mm stock rotors The Girodisc system is a direct replacement for the OE disc, they will bolt directly to the car and work with OE calipers perfectly. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair
Girodisc S-S Pads (Rear) SS-0810
Girodisc Girodisc S-S Pads (Rear) SS-0810 $200.00
The Girodisc S/S or "street/strip" pads represent the ultimate in high performance brake pads. The semi-metallic compound maintains a consistent coefficient of friction from 0o to 1000o F, making them an ideal option for people who are looking for a dual-purpose pad that works really well on both the street and the race track. The formula has very little compressibility, ensuring a very firm pedal and immediate bite and making the S/S pads a favorite among autocrossers and drivers who demand the most out of their street cars. Inevitably, these pads will dust more than Girodisc Magic Pads, but with the Girodisc anti-noise shims that come on every set of pads they will not make any noise if they are bedded-in properly. We recommend always replacing pads as a whole car set when switching compounds. All S/S pads come with anti-noise shims pre-installed and included in the price. If you have any questions, give us a call at 888-748-7223. We're happy to help!
Girodisc S-S Pads (Front) SS-1405
Girodisc Girodisc S-S Pads (Front) SS-1405 $325.00
The Girodisc S/S or "street/strip" pads represent the ultimate in high performance brake pads. The semi-metallic compound maintains a consistent coefficient of friction from 0o to 1000o F, making them an ideal option for people who are looking for a dual-purpose pad that works really well on both the street and the race track. The formula has very little compressibility, ensuring a very firm pedal and immediate bite and making the S/S pads a favorite among autocrossers and drivers who demand the most out of their street cars. Inevitably, these pads will dust more than Girodisc Magic Pads, but with the Girodisc anti-noise shims that come on every set of pads they will not make any noise if they are bedded-in properly. We recommend always replacing pads as a whole car set when switching compounds. All S/S pads come with anti-noise shims pre-installed and included in the price. If you have any questions, give us a call at 888-748-7223. We're happy to help!
Pagid Racing Brake Pads No. 8081
Pagid Pagid Racing Brake Pads No. 8081 from $580.96
RS 14: Outside the track day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RS14 offers very low heat conductivity, resulting in lower caliper and brake fluid temperatures. RS14 offers consistent levels of performance and much longer life than competitors' products without excessive rotor wear, offering the driver supreme confidence. The PAGID RS14 (Black) is a high-friction-value ceramic compound with very good modulation, high fade resistance, low heat conductivity, and a good wear rate up to a constant temperature of 1,200°F (650°C). It's kind on rotors, with visible grooving but no tendency to crack them. RS14 is our most popular ceramic-based friction material. It will tolerate much higher working disc temperatures than PAGID RS4-2, extending fade resistance. RS14 is used as an OEM material and supplied as an upgraded track day pad by Lotus Motorsport. It has been shown to exhibit optimum levels of braking force, control and modulation on popular track-day cars such as the Lotus Elise and Caterham 7.  RSL 29: Designed primarily for endurance racing, due to consistent levels of performance and user friendliness many competitors use this material for sprint and short distance races also. RS29 has also found favor in the growing track-day market due to the high level of control, good cold performance, long life, and low rotor wear. The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport.  Based on the RS14, a slight reduction of the friction value improves modulation and longevity. The friction value remains high enough for cars without power-assisted brake systems, ensuring low effort on the brake pedal. Constant temperatures up to 1,100°F (600°C) are possible. This combination of friction value, fading stability, and low wear rates on pads and rotors is unmatched. Due to its excellent release characteristics and controllability, PAGID endurance materials are also often used for sprint races. This material provides very good levels of performance and response at all temperature levels; only slight temperature inputs are required to bring the pad up to its optimum performance level. A favorite with endurance racers at events such as Le Mans, Daytona, Spa, Nurburgring, etc. Due to the exceptional pad life and very low wear on brake discs it has been possible to run 24 hours without a change of pads or discs. This has proved suitable for applications running very high disc temperatures.
Pagid Racing Brake Pads No. 1287
Pagid Pagid Racing Brake Pads No. 1287 from $364.39
    Fits These Vehicles: Make Model Build (Year) Front Rear Aston Martin Vanquish 03 - 08 X   Audi R8 07 - 15   X Audi R8 (2nd generation) 15 -   X Audi R8 (2nd generation) [ceramic brakes] 15 -   X Audi R8 [ceramic brakes] 09 - 15   X BMW M4 [F82] [ceramic brakes] 14 -   X Dodge Viper Competition Coupe 03 - X X Dodge Viper SRT-10 04 - X X Ferrari 512 Testarossa 92 - 96 X   Ferrari F40 Street and race 87 - 92 X X Ferrari F50 95 - 97 X X Lamborghini Diablo [Brembo brakes] 92 - 99 X X Lamborghini Gallardo 04 - 13   X Lamborghini Gallardo [ceramic brakes] 04 - 13   X Lamborghini Huracán [ceramic brakes] 14 -   X Lamborghini Huracán [iron brakes] 14 -   X Lamborghini Murciélago [non ceramic] 01 - 10 X X McLaren F1 / shape rear on inquiry 92 - 98 X   Nissan R35 GTR 08 -   X RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RSC 1: RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.      
D2-083 Girodisc Rear Replacement Rotor Rings
Girodisc D2-083 Girodisc Rear Replacement Rotor Rings $800.00
FITS: Nissan GTR (2009-2011) (2012+) REPLACEMENT ROTOR DISCS ONLY, DOES NOT INCLUDE ALUMINUM HAT. Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.
D1-084 Girodisc Front Replacement Rotor Rings (395mm)
Girodisc D1-084 Girodisc Front Replacement Rotor Rings (395mm) $800.00
FITS: Nissan GTR (2009-2011) (2012+) REPLACEMENT ROTOR DISCS ONLY, DOES NOT INCLUDE ALUMINUM HAT. Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc replacement rotor system is a direct rotor disc replacement for the Giro Disc 2-piece hat and rotor and no modifications are necessary. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement to minimize replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.