Murcielago (2005-10)

CMS RF1 DOT4 Racing Brake Fluid Real-Life High Boiling Point Without The Real High Price RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid. RF1 Racing Brake Fluid Details Typical dry boiling point: 328º C (622º F) Typical wet boiling point: 204º C (399º F) Exceeds DOT3 & DOT4 standards Bottle size: 500 ml (16.9 fl oz) Click Here for Product MSDS Sheet A Word About Flushing Brake Fluid All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.

Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Lamborghini Murcielago Late (2005-2010) These Girodisc iron rotors are a direct replacement for the OE brake discs with no modifications. By upgrading your brakes with lightweight high performance replacements, as opposed to a big brake kit, your factory brake bias and ABS effectiveness are maintained. These Girodisc front rotors are approx 18.2 lbs vs. 22.0 lbs for the stock units. This reduction in rotational and unsprung weight allows for quicker acceleration, stronger braking, and sharper suspension response The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair

    Fits These Vehicles: Make Model Build (Year) Front Rear Aston Martin Vanquish 03 - 08 X   Audi R8 07 - 15   X Audi R8 (2nd generation) 15 -   X Audi R8 (2nd generation) [ceramic brakes] 15 -   X Audi R8 [ceramic brakes] 09 - 15   X BMW M4 [F82] [ceramic brakes] 14 -   X Dodge Viper Competition Coupe 03 - X X Dodge Viper SRT-10 04 - X X Ferrari 512 Testarossa 92 - 96 X   Ferrari F40 Street and race 87 - 92 X X Ferrari F50 95 - 97 X X Lamborghini Diablo [Brembo brakes] 92 - 99 X X Lamborghini Gallardo 04 - 13   X Lamborghini Gallardo [ceramic brakes] 04 - 13   X Lamborghini Huracán [ceramic brakes] 14 -   X Lamborghini Huracán [iron brakes] 14 -   X Lamborghini Murciélago [non ceramic] 01 - 10 X X McLaren F1 / shape rear on inquiry 92 - 98 X   Nissan R35 GTR 08 -   X RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RS 14: The PAGID RS14 (Black) is a high friction value ceramic compound with very good modulation and high fade resistance. A very popular, aggressive pad with strong initial bite and high torque. In addition to the track-day environment, RS14 has shown success in short- to medium-distance circuit racing as well as gravel and tarmac rallying. RSC 1: RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.      

Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits Lamborghini Murcielago Late (8/4 Pot) The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.