girodisc

This Girodisc iron rotor conversion is a direct replacement for the OE carbon ceramic disc with the addition of the provided caliper spacers. At 394mm diameter, these Girodisc rotors are slightly larger than the 380mm OEM rotors. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair

FITS: MCLAREN 720S (CCB Rotor) The Girodisc system is a direct replacement for the OE CCB disc on all vehicles that came equipped with CCB rotors from the factory. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is made from cast iron to the same specification and material as used by professional racing organizations. It is a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 10 high strength alloy steel drive pins, manufactured by Girodisc to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor when needed. When used with performance pads and hi-temp fluid, you have what amounts to a truly amazing solution to overheating or warping rotors. Sold/Priced per pair.

Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Chevrolet Camaro ZL1 Gen 6 The Girodisc system is a direct replacement for the OE disc, but a different brake pad with an annulus (pad swept area) of 66mm or less must be used. We strongly recommend the Pagid 8081. This is done to bring the weight of the disc down. The OEM rotor utilizes a pillar vane design which is horribly inefficient and, with no way of effectively dissipating heat, it heat soaks very easily. Chevrolet chose the easy solution and made the rotor extremely heavy to combat that heat. We weighed an OEM rotor at 32.5 lbs! Girodisc took the functional route instead, engineering a shorter-annulus ring for a total rotor weight of 28.0 lbs. This design utilizes 72 directional cooling vanes for an incredibly efficient and robust package. The necessary pad shape is very common and also found on other Camaro and Corvette applications equipped with 6 piston calipers. If there is a specific pad compound you're after please contact us directly to provide the correct part numbers. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair

Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits Audi B9 RS5 The GiroDisc system is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

Discovery Parts is an authorized dealer for Girodisc products and one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits BMW F8x M2/M3/M4 w/ OEM CCB The Girodisc system is a direct replacement for the OE rotors. No modifications are necessary. The disc will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency.The central hat section of our rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from our own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The pins are secured by class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor when needed. Sold/Priced per pair.

Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Nissan GT-R (DBA) 2012+ w/ 390mm stock rotors The Girodisc system is a direct replacement for the OE disc, they will bolt directly to the car and work with OE calipers perfectly. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair

Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits Porsche 991 GT3 Cup Car (Front) The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight (approx. 8 lbs) allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Chevrolet Camaro ZL1 Gen 5 The Girodisc system is a direct replacement for the OE disc, they will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair

Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits Corvette C8 The GiroDisc system is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

Discovery Parts is an authorized dealer for Girodisc products. As one of the largest stocking dealers in the country, we ship most Girodisc products the same or next business day to ensure we meet your delivery deadline. Fits Nissan GT-R (CBA) 2007-2011 w/ 380mm stock rotors The Girodisc system is a direct replacement for the OE disc, they will bolt directly to the car and work with OE calipers perfectly. The central hat section of the Girodisc rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved-vane design, developed in racing to act as a centrifugal pump forcing cool air through the disc. The disc and hat have a floating mount system, which utilizes 12 high-strength alloy steel drive pins, manufactured in the US by Girodisc and cadmium plated for long-lasting corrosion resistance. These pins take the loads from braking while maintaining the axial and radial float between the hat and disc. They are secured by class 12.9 cap screws and hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise springs on the disc side, allowing the iron disc to expand as it heats up while eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the brake pads. Once the Girodisc system is in place, you simply replace the cast iron discs when needed. This reduces cost over time by allowing you to re-use the aluminum central hats. Sold/priced per pair

This Girodisc system is a 380mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the one-piece OEM GT4 Clubsport steel brakes. The A1-266 will bolt directly to the GT4 ClubSport and work perfectly with your OEM calipers. There are two main reasons for replacing your OEM rotors: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the slotted Girodisc A1-266 will far outlast the OEM drilled rotors. When subjected to intense heat in a racing or track-day environment, the drilled holes in the OEM rotors originate cracks which can lead to rotor failure. When paired with the Girodisc A2-266 rear rotors, your factory brake bias and ABS efficiency are maintained. When used with Pagid or PFC performance brake pads, and Discovery Parts RF1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes eight to ten high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

FITS PORSCHE 911 GT3/GT3RS/GT2RS (2021+) FRONT WITH STEEL BRAKES The Girodisc system is a direct replacement for the OE disc on the 992 GT3, GT3RS, and GT2RS with OEM iron rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight, high performance replacements -- as opposed to a big brake kit -- your factory brake bias and ABS efficiency are preserved.The central hat section of our rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The rotor is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to their own specifications and cadmium plated for long-lasting corrosion resistance. These pins take the load from braking while maintaining the axial and radial float between the hat and disc. The pins are secured by Class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion, eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed.When used with Pagid or PFC racing brake pads and hi-temp RF1 racing brake fluid, you have what amounts to a truly amazing solution to overheating or warping rotors.If your car same with OEM center lock wheels please select the center lock drive pin option.Sold/priced in pairs.

Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits Tesla Plaid Front Only The GiroDisc system is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

DiscoveryParts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Dodge SRT Hellcat ('21+) Front Axle The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid, you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

Discovery Parts is an authorized dealer for Girodisc products and one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.   Introducing the GiroDisc 2-piece rotors, engineered as a direct replacement for the front rotors on the G80 M3, G82/83 M4, and G87 M2 models without carbon ceramic brakes. Our advanced 2-piece, fully floating assemblies significantly reduce unsprung weight and rotating mass from the front axle, enhancing vehicle performance. Crafted from a proprietary high-carbon iron casting, our rotor rings are meticulously machined to GiroDisc's stringent specifications. This superior metallurgy ensures exceptional durability, while the 72 curved vanes function as a centrifugal pump, effectively cooling the rotors during intense use. The innovative 2-piece design features a reusable hat that can be easily attached to new rings (part number D1-282) when replacement is necessary. All major components, including the hats, rotor rings, and drive pins, are manufactured in-house at our Bellingham, WA facility using domestically sourced materials. The hat is constructed from 6061-T6 aluminum and finished with a black anodized coating. The drive pins, made from a high-strength steel alloy, are cadmium-plated for enhanced corrosion resistance. Each rotor assembly includes spring clips and Belleville washers, ensuring race-ready float while maintaining street-friendly noise levels. We recommend replacing the rotor rings when the thickness reaches 34mm or if a crack extends to the edge of the ring. Priced and sold per pair.

FITMENTS (FRONT or REAR): Ferrari F430 Ferrari 360 Modena DiscoveryParts is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. These GiroDisc 2-piece rotors serve as direct replacements for the front rotors found on Hyundai Elantra N, Kona N, and i30 N models. Featuring fully floating assemblies, they effectively reduce unsprung weight and rotating mass on the vehicle's front axle. Crafted from a proprietary casting of high-carbon iron tailored to GiroDisc’s exacting standards, the rotor rings boast superior metallurgical properties, ensuring enhanced durability. The inclusion of 48 curved vanes acts as a centrifugal pump, drawing air in through the hub to facilitate efficient cooling during intense use. The 2-piece design incorporates a reusable hat, facilitating easy attachment to new rings (part number D1-327) when replacement is needed. All primary components, including hats, rotor rings, and drive pins, are meticulously manufactured in-house at our Bellingham, WA facility using domestically sourced materials. The hat is constructed from 6061-T6 aluminum and features a durable black anodized finish. Drive pins are crafted from a high-strength steel alloy and coated with cadmium for optimal corrosion resistance. Assembly includes spring clips and Belleville washers to ensure race-ready float while maintaining street-friendly noise levels without loose hardware. We recommend replacing the rotor rings when they reach a minimum thickness of 28mm or if a crack extends to the ring's edge. These rotors are sold and priced per pair.