Alpinestars
Alpinestars Race v4 Nomex Socks
$52.95
Alpinestars Race v4 Nomex Socks
 Alpinestars Race v4 Socks are lightweight, durable and ergonomically designed to meet the demands of the world top drivers. Certified to FIA homologation standards, these socks offer excellent protection from heat transfer and flat seams for long-lasting comfort.
ALPINESTARS RACE V4 NOMEX SOCK PROTECTION
Certified to the new FIA 8856-2018 homologation standard.
AiM Sports
AiM MyChron External Power Cable
$52.00
AiM Sports MyChron External Power Cable
If you're not powering your AiM MyChron by connecting it to your kart, you'll need this external power cable in order to provide enough juice for your MyChron. Installation is quick and easy.
Two meters (6.6 feet) in length.
Note: this cables typically takes 3 to 5 business days to ship.
AiM Sports
AiM Solo DL to OBD-II Connector (Old Solo DL)
$52.00
AiM CAN 7-Pin to OBD-II (K-Line Connector) Cable for Solo DL
AiM Solo DL to OBD-II Port Connection Cable On Your Car For Easy Addition of RPM and other vehicle data. One end has the K-Line (OBD-2) plug to fit the diagnostic port, and the other end has a 7-pin 712 (screw-in) connector for the Solo DL. OBD-II is also known as K-Line
This is the same cable supplied with the original AiM Solo DL for OBD-II.
Does not fit the new Solo2 DL.
AiM CAN 7-Pin to OBD-II (K-Line Connector) Cable for Solo DL Details:
Manufacturer: AiM
Manufacturer part number: V02569010
AiM Alternate part number: MC-568
End 1: AiM 7 Pin 712 (thread on)
End 2: OBD-2 (K-Line)
Fits AiM Solo: No
Fits AiM Solo DL: Yes
Fits AiM Solo 2: No
Fits AiM Solo2 DL: No
Note: Not compatible with the original SmartyCam (gray unit with the viewing screen on top) or the later SmartyCam HD "Rev 1". The version 1 can be identified by a 7/8" diameter lens with either a 67 or 87 degree field of view, and a viewfinder flush with the front of the housing. Later SmartyCam HD Rev 2 had a larger 1 3/8" OD lens marked as 60 or 120 degree field of view and a cover over the front viewfinder held on by 8 screws.
AiM Sports
AiM Solo2 DL RPM and Power Wiring Harness
$52.00
AiM Solo2 DL RPM and Power Wiring Harness
The AiM V02589020, called the AiM Solo2 DL RPM Input Wire, is used to connect your AiM Solo2 DL to any vehicle that does not have an ECU (such as older cars). On the bottom right of your Solo2 DL there is an eight-pin connector that you can connect to the low voltage side of your ignition coil. The peak can be anywhere from +150 to +400 V or from a square wave with a peak of +5 to +50 V.
If you have a vehicle with an MSD Ignition box, this is your easiest way to log RPM. By connecting the positive and negative wires, your Solo2 DL unit will automatically top off the internal battery and power all down line appliances, such as a SmartyCam or other powered device.
AiM Solo2 DL RPM Input Wire Details
Manufacturer: AiM Sports
Manufacturer part number: V02589020
End 1: male 712 8-pin screw-on
End 2: flying leads (open wires) 12 VDC positive , negative, and RPM input
Length: 2 meters (6.6 feet)
AiM Solo2 DL RPM Input Wire Uses
Solo2 DL to older external ignition coil engines
Solo2 DL to RPM tach lead
Solo2 DL to MSD Ignition box
AiM Sports
INTERNAL: AiM Solo2 DL to OBDII Connector
$52.00
AiM CAN 7-Pin to OBDII (K-Line Connector) Cable for Solo2 DL
AiM Solo2 DL to OBDII Connection Cable On Your Car For Easy Addition of RPM and other vehicle data. One end has the K-Line (OBDII) plug to fit the diagnostic port, and the other end has a 7-pin 712 (screw-in) connector for the Solo2 DL. OBDII is also known as K-Line
This is the same cable supplied with the original AiM Solo2 DL for OBDII connection.
Does not fit the original Solo DL.
AiM CAN 7-Pin to OBDII Cable for Solo2 DL Details
Manufacturer: AiM
Manufacturer part number: V02589040
End 1: AiM 7 Pin 712 (thread on)
End 2: OBD-2 (K-Line)
Fits AiM Solo: No
Fits AiM Solo DL: No
Fits AiM Solo2: No
Fits AiM Solo2 DL: Yes
AiM Sports
AiM Solo2 DL CAN/RS232 Wiring Harness (New Solo2 DL)
$52.00
AiM Solo2 DL CAN/RS232 Wiring Harness
If you're moving your AiM Solo2 DL from one car to another and need a harness for power and data input, this is your cable. If you are putting a Solo2 DL into an older vehicle and need a power supply cable, use this and use only the "+" and "-" wires (fold back the CAN inputs).
The AiM V02569050 harness connects your Solo2 DL to your ECU via your vehicle's CAN or RS232 bus wiring. One end has a 7-pin 712 (screw-in) connector to fit the Solo2 DL, and the other has six non-terminated wires (CAN+, CAN-, RS232RX, RS232TX, Power, and Ground).
Does not fit the original AiM Solo or Solo DL.
AiM Solo2 DL CAN/RS232 Wiring Harness (New Solo 2 DL) Details
Manufacturer: AiM Sports
Manufacturer part number: V02589050
Fits Solo DL: No
Fits Solo2 DL: Yes
Fits Solo Base Model: No
Fits Solo2 Base Model: No
Pins on AiM Solo2 DL Side: 7 Pin Thread on connector
Vehicle Chassis Ends: six non-terminated wires
Chassis End Wiring Break Out: Red=+12 VDC, Black=Ground, Blue=ECU RS232TX, Blue=ECU RS232 CAN-, Gray ECU RS232 RX, Gray CAN+
AiM Solo2 DL CAN/RS232 Wiring Harness Wiring Code
Red: +9 to +15 VDC
Black: Ground
Grey: CAN+
Blue1: CAN-
Gray: ECU RS232 RX
Blue1: ECU RS232TX
1 Note: both blue wires are the same color, but each wire has an identifier tag stating the connection type.
AiM Sports
AiM Solo2 DL to OBDII Connector
$52.00
AiM CAN 7-Pin to OBD-II (K-Line Connector) Cable for Solo2 DL
AiM Solo2 DL to OBDII Port Connection Cable On Your Car For Easy Addition of RPM and other vehicle data. One end has the K-Line (OBDII) plug to fit the diagnostic port, and the other end has a seven-pin 712 (screw-in) connector for the Solo2 DL. OBDII is also known as K-Line.
This is the same cable supplied with the original AiM Solo2 DL for OBDII connection.
Does not fit the original Solo DL.
AiM CAN 7-Pin to OBDII Cable for Solo2 DL Details
Manufacturer: AiM
Manufacturer part number: V02589040
End 1: AiM 7 Pin 712 (thread on)
End 2: OBDII (K-Line)
Fits AiM Solo: No
Fits AiM Solo DL: No
Fits AiM Solo2: No
Fits AiM Solo2 DL: Yes
AiM Sports
AiM Solo2 DL Vehicle Power Wiring Harness
$52.00
AiM Solo2 DL Vehicle Power Wiring Harness
Now you can power your AiM Solo2 and Solo2 DL for your entire endurance race without the need to charge the battery. The power cable that comes with the AiM Solo2 in the package is set up for a cigarette lighter connection, but this is a hard wire connection for true race cars. This harness connects your AiM Solo2 to your vehicle's fuse box wiring. One end has a 5-pin 712 (screw-in) connector to fit the Solo, and the other has two non-terminated wires (Power and Ground).
AiM Solo2 DL Vehicle Power Wiring Harness Details
Manufacturer: AiM Sports
Manufacturer part number: V02589010
Fits Solo DL: No
Fits Solo2 DL: Yes
Fits Solo Base Model: No
Fits Solo2 Base Model: Yes
Pins on AiM Solo Side: 5-pin thread-on connector
Vehicle Chassis Ends: two non-terminated wires for power and ground
If you are putting an AiM Solo2 DL into an older vehicle and need a direct to battery/fuse box power supply cable, use this harness for a neat, easy installation.
AiM Sports
AiM SmartyCam External Power Cable
$52.00
AiM Sports SmartyCam External Power Cable
If you're not powering your AiM SmartyCam by connecting it to a Solo2 DL or an AiM Sports Dash, you'll need this external power cable in order to provide enough juice for your SmartyCam to record every session. Installation is quick and easy.
Two meters (6.6 feet) in length.
Note: this cables typically takes 3 to 5 business days to ship.
Longacre
Longacre Long Mirror Brackets - 1.50" ID (Set Of 2)
$51.99
Longacre Long Mirror Brackets (Set Of Two)
Set of two billet aluminum mounting brackets for Longacre wide-angle racing mirrors. Installation requires no welding, these clamp firmly to any 1.50" OD tubing.
Longacre Long Mirror Brackets Details:
Manufacturer: Longacre
Manufacturer part no.: 52-22541
Material: CNC-machined billet aluminum
Finish: black anodized
Length adjustment: 2.0" to 5.5"
No welding - bolts to 1.50" OD roll bar tubing
Set of two brackets
Alpinestars
Alpinestars Sequence Youth Neck Support
$51.95
Alpinestars Sequence Karting Neck SupportAlpinestars Sequence Youth Neck Support is optimized for track-day performance with reliable cooling, lightweight construction, and race-ready durability.
Designed and developed specifically for younger riders, the Sequence Youth Neck Roll is the starting point on a junior driver’s journey to the Bionic Neck Support. Ergonomically profiled for a young rider’s body requirement, the Sequence Neck Roll’s frame is designed to transfer impact energy away from the upper neck.
SEQUENCE NECK SUPPORT CONSTRUCTION
New hybrid kids neck protection with extended tail for high position stability.
Ergonomic designed and engineered shape to fit kids from 6 – 10 yrs. and from 10-14 yrs.
Double density core is made from a soft PU foam base embedding a hard layer EVA for energy dissipation.
Bottom and internal soft section (neck side) provides comfort for the shoulder and neck, hard section on the upper part to give stability and provides force distribution when the helmet is impacting.
SEQUENCE NECK SUPPORT KEY FEATURES
Easy to use soft strap closure on the front part.
Highly compatible with all other protectors and jackets.
External cover can be pulled of core for washing by Velcro opening on the rear.
AiM Sports
AiM Sports Thermocouple Extension Cable (5 feet)
$50.00
AiM Sports Thermocouple Extension Cable (5 feet)
Extension cable to link a thermocouple temperature sensor to your MyChron data-logger dash. Features one 712 3-pin male connector and one K-style female connector. Cable length is 5.0 ft. (1.5 meter).
Rental
Daily Rental of HANS Device at AMP
from $50.00
Rent An Up-To-Date HANS Device Right At AMP!
Discovery Parts store in the AMP paddock carries a full complement of HANS devices to make sure every driver is safe out on the race track.
You can rent a HANS device for up to four days. Your rental is due back to Discovery Parts by 5pm on the final day of your rental.
Rental
Daily Rental of One Piece Race Suit at AMP
from $50.00
No Fire Suit? No Problem, We'll Rent You One!
Rent a one-piece, multi-layer SFI rated fire suit at the Discovery Parts store right in the Atlanta Motorsports Park paddock. Clean, comfortable, and professionally-maintained, our rental suits will keep you safe while you're out on the AMP race track.
Roux Helmets
Roux Peak Visor White Fits Roux R-1 Helmets
$50.00
Roux Peak Visor White Fits Roux R-1 Helmets
Analogous to the brim of a hat, peak visors are designed to keep the sun out of your eyes. Roux peak visors will fit your your Roux R-1 Helmet perfectly.
Roux Peak Visor White, Fits Roux R-1 Helmets Details:
Manufacturer: Roux
Manufacturer part number: RXHS05-15G00
Color: Gloss White
Roux hardware kit ROU-RXHS07-15D is required to install this peak visor
