New products

AiM CAN 7-Pin to OBD-II (K-Line Connector) Cable for Solo DL AiM Solo DL to OBD-II Port Connection Cable On Your Car For Easy Addition of RPM and other vehicle data. One end has the K-Line (OBD-2) plug to fit the diagnostic port, and the other end has a 7-pin 712 (screw-in) connector for the Solo DL. OBD-II is also known as K-Line This is the same cable supplied with the original AiM Solo DL for OBD-II. Does not fit the new Solo2 DL. AiM CAN 7-Pin to OBD-II (K-Line Connector) Cable for Solo DL Details: Manufacturer: AiM Manufacturer part number: V02569010 AiM Alternate part number: MC-568 End 1: AiM 7 Pin 712 (thread on) End 2: OBD-2 (K-Line) Fits AiM Solo: No Fits AiM Solo DL: Yes Fits AiM Solo 2: No Fits AiM Solo2 DL: No Note: Not compatible with the original SmartyCam (gray unit with the viewing screen on top) or the later SmartyCam HD "Rev 1". The version 1 can be identified by a 7/8" diameter lens with either a 67 or 87 degree field of view, and a viewfinder flush with the front of the housing. Later SmartyCam HD Rev 2 had a larger 1 3/8" OD lens marked as 60 or 120 degree field of view and a cover over the front viewfinder held on by 8 screws.

Schroth Rallye Cross ASM 4 Point Tuning Harness The Schroth Rallye Cross ASM is among the most basic harnesses we sell. There are no quick disconnects between the front and rear sections, just four straps that each bolt to the car (the shoulder belts can also be wrapped around your roll bar). The Schroth Rallye Cross ASM is a four-point harness with Schroth's patented ASM technology, which makes it as safe as a four-point belt can be. What differentiates it from the Schroth Rallye 4 is the shoulder straps. DIRECT MOUNTED SHOULDER STRAPS ADD SAFETY Where the Rallye 4 has a quick-disconnect buckle between the front section of the harness and the tail straps, the Schroth Rallye Cross ASM has two independent shoulder straps that go directly to the mounting point. These shoulder straps can be mounted either by wrapping them around a roll bar/harness bar or by bolting them to the bar or the chassis. The Schroth Rallye Cross ASM harness is perfect for someone who's still using stock seats, but wants a safe harness solution for track driving in a car where access to the back seat is not necessary, or in cars with no back seat to begin with. Note: The harness attachment points for the shoulder straps must be structural. They must not be bolted only to sheet metal or to rear child-seat anchors. They must be properly reinforced, either from the factory or by the use of backing plates. SCHROTH RALLYE CROSS ASM 4 POINT HARNESS DETAILS Manufacturer: Schroth Meets FMVSS 209 specification for use on US roads Waist belt ends: sewn in, bolt to chassis Shoulder belt ends: choose wrap-around or bolt-on Click here for operating and installation instructions In light of recent testing, all Rallye Cross harnesses no longer have a specific Left or Right (Driver or Passenger) side. This harness is not compatible with a HANS or any other head-and-neck restraint device. This harness is not approved for all vehicles and may exceeded the maximum shoulder strap downward angle recommended by Schroth. If you have questions about using it in your car, please give us a call at (888) 748-7223. 

Stilo Visor Stocking Bag Stilo gives you one free Visor Stocking Bag with every new shield, but having an extra is a great idea to make sure your Stilo shields have the longest life possible. Constructed of soft micro-fiber with a draw string and ball lock, this Stilo visor stocking bag keeps your Stilo visor protected. Works perfectly with all Stilo ST4 and ST5 Composite, Offshore, Carbon, 8860, and 8860 Zero helmet shields. Stilo Visor Stocking Bag Details: Manufacturer: Stilo Manufacturer part number: YY0014 Fitment: Stilo ST4, and ST5 Composite, Offshore, Carbon, 8860, and 8860 Zero helmet shields  

Schroth Rallye 4 ASM Harness The Schroth Rallye 4 is the de-facto standard for anyone looking for a simple, safe, DOT-approved 4 point harness. The technology built into this harness puts it in a category above belts made by other manufacturers. Schroth's years of testing and motorsport experience are brought to bear in making this 4-point harness as safe as it can be. SCHROTH TECHNOLOGY STANDS ABOVE THE REST There are two main reasons why the Schroth harnesses are the only safe 4-point harnesses: first, ASM technology; second, the ability to install the harness using stock mounting locations. ASM stands for "Anti-Submarining". It's an extra flap of technical material sewn into the inboard shoulder belt that prevents you from sliding underneath the lap belt in a crash. In a typical 4-point harness, the two shoulder straps restrain your upper body equally, keeping your chest from moving forward but also pulling up on the lap belts. This allows your pelvis to slide under the lap belt, which can cause serious damage. With ASM, the shoulder belts will elongate at different rates, allowing your torso to turn slightly which forces your pelvis down into the seat cushion. Upon rebound, you will be placed back in an upright position with the belt correctly placed over your body. STOCK MOUNTING POINTS ARE THE STRONGEST Being able to mount a Schroth Rallye 4 ASM harness to stock mounting locations means you're using the points engineered by the car maker to withstand extremely high forces for a specified length of time. That means the mounting bolts won't pull out of the sheet metal. It also means (in the case of a Schroth harness) that you can retain the use of your stock 3-point harness, allowing you the use of the backseat of your car. If you have the need to transport passengers (or cargo) in your backseat, it is possible to disconnect the tailstrap (a feature only Schroth has) and use your normal 3 point belts. See Schroth Harness Installation Checklist Here

Chillout Systems Carbon Fiber Air Duct Plenum Forcing fresh air to your cooler is the most efficient way to increase cooling performance and reduce amp draw from your electrical system. This plenum fits perfectly to the intake side of your Quantum Cooler, allowing much cooler air to be forced through the system via any three-inch duct (cooler, ducting, and intake scoop not included). A minimum Uber3 blower (sold separately) should be used in conjunction with the plenum in order to cool properly. This carbon fiber plenum attaches via automotive-grade adhesive tape, creating a firm seal to keep the cooler pressurized with incoming cool air. This forces cool air all the way through the system and back out the exhaust side of the cooler, the most efficient way to reach maximum cooling capacity. Coupling the Chillout Systems Air Duct Plenum with your Quantum Cooler ensures no cool air is wasted, maximizing the effectiveness of the system.  

Schroth B23A Bendable Harness Snap End Kit Schroth B23A harness ends are bendable and make racing harnesses easier where there is very little clearance. The Schroth B23A bendable snap-on harness adapter lets you bolt one end to the chassis, bend it to the needed shape, and attach your harness snap end. Schroth B23A Bendable Harness Snap End Kit Details: Manufacturer: Schroth Manufacturer part number: B23A Manufacturer alternate part number: SR 01324 Bendable Fittings: Yes (2) Bolts: Yes (2) 7/16-24 Wavy Washers: Yes (2) Combination Washers: Yes (2) The B23A End Fitting Kit is a set of bolt in brackets that are usually sewn into 2" Lap belts. Schroth slang calls it a "Rallye End" kit because it usually comes on the street legal Rallye style belts. Like the 01323 kit, it is designed to be bent. These pieces are commonly used in Porsche applications where space for an Eye bolt is insufficient. This bracket can be bolted to the car, then bent so that a Snap-In bracket can be used to fix the harness to the bracket. We use Schroth B23A brackets in many applications where stock mounting locations do not leave sufficient space, or if the thread pitch is different from the eye bolts. If you have a Miata, S2000 or are putting a large/very large seat in a full interior car this is the harness mount kit you want.

Stilo ST5 Thin 2mil Tearoff Pack qty 30 (3 Sleeves of 10) Protect Your Stilo ST5 Helmet Shield From Rocks, Dirt, and Debris with these 2 mil thick tearoffs. Measuring 2 mil thickness (the most popular thickness for dirt track racers), it is intended for road racing and/or dirt track use. This package of 2 mil tear-offs are in 3 stacks of 10 per package (30 tear-offs in all). Now you can greatly extend the life of your Stilo ST5 shield by drastically reducing pitting and scratches. Stilo ST5 2mm Tearoff Pack Quantity 30 (3 Sleeves of 10) Details: Manufacturer: Stilo Manufacturer part numbers:10259C Thickness each: 2 mil Gradient: Clear Fits All Stilo ST5 Helmets: Yes Fits All Stilo ST4F and Stilo ST4W Helmets: No 3 Stacks of 10 tear-offs glued together Note: This is the thinner of tearoffs (2 mil) for your Stilo ST5 series helmets. It is used primarily in Dirt Track Racing where you need more pulls in a race

Racing Radios Two-Way Headset with Overhead Strap The Racing Radios classic styled over-the-head headset is reversible, so your microphone can cross over your left or right cheek. The single over the head style is perfect for crew chiefs that prefer not having the dual strap system (one on top and also across the back). DETAILS Manufacturer: Racing Radios Manufacturer part number: RRH158 5 pin cable connection Additional audio input (3.5mm) jack Push-To-Talk Switch PTT on Earcup Noise-canceling adjustable microphone Mounted on one of the earcups is a 3.5mm female jack for listen only through your ear cup speakers. This is most commonly used as a scanner in addition to your primary vehicle communications.

HANS Device Padding Set - Foam HANS Replacement Foam Padding Set is a racer's favorite. Make your HANS more comfortable and look new again with HANS Foam Padding. The HANS Device Replacement Padding Set For HANS Devices Includes Two Shoulder Pads. Soft foam may address comfort concerns, especially from those with a ridge where a broken collar bone has healed. Fits medium and large devices only. These are factory installed on all HANS adult devices. DETAILS Manufacturer: HANS Manufacturer part numbers: K9005, K9007, K9024, K9008 Colors: Black, Blue, Red, Yellow Fitment: All HANS devices in Medium & Large Sizes Fits Youth devices: No

Hans Device Gel Padding Set Designed for endurance racers or anyone who would like added comfort from their HANS device, the HANS Gel Pad upgrade kit is for you. Hans device Gel Padding Set Details Manufacturer: Hans Colors: Black, Blue, Red, Yellow Attachment: Velcro Manufacturer part number black: K9010 Manufacturer part number red: K9025 Manufacturer part number blue: K9012 Manufacturer part number yellow: K9013 Not just for body builder/swimmer body shapes, the HANS gel padding kit is also for anyone with any previous shoulder surgeries/stainless/titanium or other upgrades. The Hans Accessory Gel Padding Set for HANS Devices includes two Shoulder Pads. Soft medical grade gel pad may address comfort concerns, especially from those with a ridge where a broken collar bone has healed. Fits medium and large devices only. Hans Gel Padding Set is a racer's favorite. Make your HANS more comfortable with Hans Gel Padding. Medical grade gel padding feels great even after a double stint in the your next endurance race.

Alpinestars GP Pro Comp Race Suit - Boot Cuff Leg The Alpinestars GP Pro Comp Racing Suit is built for drivers who need certified fire protection, lightweight comfort, and unrestricted movement behind the wheel. Certified to FIA 8856-2000 and SFI 3.2A/5 standards, this three-layer racing suit delivers serious protection while maintaining a breathable, athletic fit for long sessions in the car. Designed with Alpinestars’ fully floating arm construction, pre-curved arms and legs, and strategically placed stretch panels, the GP Pro Comp suit helps reduce material resistance while driving. The bootcut leg design, ribbed wrist cuffs, soft collar, and adjustable belted waist all work together to keep the suit comfortable, secure, and race-ready. Alpinestars GP Pro Comp Racing Suit Features Certified to FIA 8856-2000 homologation standard SFI 3.2A/5 certified for competition use Three-layer lightweight construction for protection and comfort 100% aramid outer shell fabric for heat and flame resistance Breathable lining helps improve driver comfort Alpinestars fully floating arm construction reduces restriction while driving Stretch knit panels at the crotch, waist, and underarms for mobility Pre-curved arms and legs for an optimized seated driving position Ribbed stretch wrist cuffs help prevent bunching Bootcut leg construction for comfort with racing shoes Premium YKK double-slider zipper for versatile fit adjustment Thigh pockets provide convenient storage Tall ribbed collar improves comfort and coverage Adjustable collar and belted waist for a precise fit Flat shoulder seams improve comfort under harnesses Shoulder epaulette construction assists driver extraction in an emergency Athletic/regular fit Weight: 305 g/sqm Built For Protection And Driver Comfort The GP Pro Comp uses a three-layer construction with an aramid outer shell to provide the heat and flame resistance required for serious motorsport use. Its FIA and SFI certifications make it suitable for a wide range of racing organizations, while the breathable lining helps keep the driver more comfortable during long sessions or hot race weekends. Optimized Fit For The Driving Position Alpinestars patterns the GP Pro Comp with anatomical arm, leg, and torso paneling to better match the seated driving position. Stretch panels at key movement zones help the suit move with the driver, while the fully floating arm construction minimizes restriction when steering, shifting, and managing controls inside the car. Race-Ready Details From the premium YKK double-slider zipper to the bootcut legs and thigh pockets, the GP Pro Comp is built with practical details that matter on race day. The ribbed wrist cuffs keep the sleeves positioned properly, the tall collar adds coverage and comfort, and the included laundry bag helps protect the suit’s fibers between events. Alpinestars GP Pro Comp Racing Suit Sizing Chart Alpinestars GP Pro Comp Racing Suit FAQs Is the Alpinestars GP Pro Comp suit FIA certified?Yes, the GP Pro Comp is certified to the FIA 8856-2000 homologation standard. Is this suit SFI approved?Yes, this suit is certified to the SFI 3.2A/5 standard. What type of construction does the GP Pro Comp use?The suit uses a lightweight three-layer construction with a 100% aramid outer shell for heat and flame resistance. Does the GP Pro Comp have stretch panels?Yes, it has stretch knit panels at the crotch, waist, and underarms to improve mobility and comfort while driving. What is the leg style?The GP Pro Comp uses a bootcut leg construction for comfort when worn with racing shoes. What fit does this racing suit have?The suit has an athletic/regular fit with anatomical paneling designed for the seated driving position.

Stilo ST5 Thick 4mil Perimeter Seal Tearoff Pack qty 9 (3 Sleeves of 3) Protect Your Stilo ST5 Helmet Shield from rocks, dirt, and debris with these 4 mil thick tearoffs. Measuring 4 mil thickness (the most popular thickness for open cockpit and harsh environment racers), it is intended for road racing and/or dirt track use. The perimeter seal system used in these tearoffs provides a tighter fit against the visor, blocking out dirt, dust, and water from getting between the visor and tearoff stack. This package of 4 mil tear-offs are in 3 stacks of 3 per package (9 tear-offs in all). Now you can greatly extend the life of your Stilo ST5 shield by drastically reducing pitting and scratches. Stilo 4 mil Perimeter Seal Tearoff Pack Quantity 9 (3 Sleeves of 3) Details: Manufacturer: Stilo Manufacturer part numbers: 3459CP Thickness each: 4 mil Gradient: Clear Fits All Stilo ST5 Helmets: Yes Fits All Stilo ST4F and Stilo ST4W Helmets: No 3 Stacks of 3 each Note: This is the thicker of tearoffs (4 mil) for your Stilo ST5 series helmets. It is used primarily in Road Racing Open Cockpit or other harsh environment race tracks

Stilo ST5 Thin 2mil Perimeter Seal Tearoff Pack qty 30 (3 Sleeves of 10) Protect Your Stilo ST5 Helmet Shield From Rocks, Dirt, and Debris with these 2 mil thick tearoffs. Measuring 2 mil thickness (the most popular thickness for dirt track racers), it is intended for road racing and/or dirt track use. The perimeter seal system used in these tearoffs provides a tighter fit against the visor, blocking out dirt, dust, and water from getting between the visor and tearoff stack. This package of 2 mil tear-offs are in 3 stacks of 10 per package (30 tear-offs in all). Now you can greatly extend the life of your Stilo ST5 shield by drastically reducing pitting and scratches. Stilo ST5 2mm Perimeter Seal Tearoff Pack Quantity 30 (3 Sleeves of 10) Details: Manufacturer: Stilo Manufacturer part numbers:10259CP Thickness each: 2 mil Gradient: Clear Fits All Stilo ST5 Helmets: Yes Fits All Stilo ST4F and Stilo ST4W Helmets: No 3 Stacks of 10 tear-offs glued together Note: This is the thinner of tearoffs (2 mil) for your Stilo ST5 series helmets. It is used primarily in Dirt Track Racing where you need more pulls in a race

Stilo ST5 Thick 4mil Tearoff Pack qty 12 (4 Sleeves of 3) Protect Your Stilo ST5 Helmet Shield from rocks, dirt, and debris with these 4 mil thick tearoffs. Measuring 4 mil thickness (the most popular thickness for open cockpit and harsh environment racers), it is intended for road racing and/or dirt track use. This package of 4 mil tear-offs are in 4 stacks of 3 per package (12 tear-offs in all). Now you can greatly extend the life of your Stilo ST5 shield by drastically reducing pitting and scratches. Stilo 4 mil Tearoff Pack Quantity 10 (4 Sleeves of 3) Details: Manufacturer: Stilo Manufacturer part numbers: 3459C Thickness each: 4 mil Gradient: Clear Fits All Stilo ST5 Helmets: Yes Fits All Stilo ST4F and Stilo ST4W Helmets: No 4 Stacks of 3 each Note: This is the thicker of tearoffs (4 mil) for your Stilo ST5 series helmets. It is used primarily in Road Racing Open Cockpit or other harsh environment race tracks

Racing Optics (X-Stack) - Impact Helmet Shields Racing Optics has the most optically advanced tear-off technology. 10 layer "distortion free" laminated tear-off system for many Impact helmets. Protect your Impact Helmet shield from rocks, dirt, and debris and extend the life of your shield by drastically reducing pitting and scratches. Racing Optics is a laminated tear-off solution for dirt and pavement forms of racing eliminating the need to apply individual tear-offs. Racing Optics has the most optically advanced tear-off technology. 10 layer "distortion free" laminated tear-off system for many Impact shields. Protect your Impact Helmet shield from rocks, dirt, and debris and extend the life of your shield by drastically reducing pitting and scratches. For racers who prefer thinner tear-offs, Racing Optics is available in X Stack (10 per stack) 2 mil with patterns specific to many Impact helmets. Each sleeve comes with three stacks of 10 Racing Optics. (total of 30) Racing Optics (X-Stack) - Impact Helmets Details: Qty in one stack: 10 Thickness: 2 mil Stacks in one package: 3 Post centers: 12 1/8" Shape: Banana Racing Optics (X-Stack) - Impact Helmets Fitment Guide: Impact Vapor Impact Vapor SC Impact Air Vapor Impact Charger Impact Super Charger Impact Draft Scorpion Exo-R2000