991.2 GT3/GT3RS/GT2RS

CMS RF1 DOT4 Racing Brake Fluid Real-Life High Boiling Point Without The Real High Price RF1 Racing Brake Fluid from CMS Performance is a fully-synthetic DOT4 brake fluid formulated to provide extraordinary performance under the most demanding high-temperature racing and track-day conditions. With a dry boiling point of 328º C (622º F), RF1 exceeds all DOT3 & DOT4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.) On the race track, brake systems operate at very high sustained temperatures, and there is perhaps no single safety system more important in racing than your brakes. No single part of that system is more critical than brake fluid. At CMS Performance, we got tired of (and a little nervous) using "racing" brake fluid at the race track that didn't live up to its claimed performance when things got hot. So we did something about it. Manufactured in partnership with Orthene, the brake fluid supplier to many teams in Formula 1, WEC, and other professional series, RF1 Racing Brake Fluid was formulated to maintain consistent viscosity, lubricity, and compressibility at the extreme system temperatures and line pressures found in racing and track days. The bottom line is this: you can spend more on brake fluid, but you can't buy higher-performance than RF1 Racing Brake Fluid. RF1 Racing Brake Fluid Details Typical dry boiling point: 328º C (622º F) Typical wet boiling point: 204º C (399º F) Exceeds DOT3 & DOT4 standards Bottle size: 500 ml (16.9 fl oz) Click Here for Product MSDS Sheet A Word About Flushing Brake Fluid All brake fluid degrades over time (not mileage), attracting water as it ages, which, at high brake temperatures, can lead to fluid boil and brake fade or failure. That's why the "wet" (aged) boiling point of any brake fluid is substantially lower than the "dry" (new) boiling point. To maintain maximum braking performance, Competition Motorsport strongly suggests replacing your brake fluid before every track event, but at least every three months if you're consistently racing and/or driving at track days. It's cheap insurance against learning about brake fade the hard way!

Pagid 4924 Racing Brake Pads Pads Fit The Following Vehicles: Porsche 991 GT3 [iron brakes] Front 2014-2019 Porsche 991 GT3 RS [iron brakes] 2016-2019 Porsche 991 Turbo [iron brakes] 2013-2019 Porsche 981 & 718 Cayman GT4 2016+ Pagid RSL 29: The Pagid RSL 29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. Pagid RSL 1: The Pagid RSL 1 has a high ceramic content with superior thermal insulation and higher heat resistance than metallic pad compounds. They feature excellent pad wear under endurance conditions, excellent rotor life, and are less aggressive than RST pads with excellent brake balance and modulation. Pagid RST 1: The Pagid RST 1 is a high average friction, aggressive pad with instant pedal response, quick release, a firm pedal at all temperatures, and a progressive torque curve. Suitable for applications with high down-force and/or very high grip. Pagid RST 3: The Pagid RST 3 is a medium-high friction metal-ceramic compound containing steel fibers and is therefore the perfect complement of the RST product family. It is exceptional in its low heat conductivity. Ideal for rally tarmac and gravel, GT cars, Touring Cars, prototype circuit racing, formula cars and club racing. It has a wide range of applications due to its combination of bite, friction and controllability.

PFC Brake Pads 1773.xx.17.44 This is an updated PFC part number; Previous part number was 7721.xx.17.44. PFC Brakes offers a wide range of sports car applications. Each PFC product is meticulously created to the highest performance and technology expectations. For PFC, we take pride in the accomplishments of the drivers and race teams that run our product. With More Championships than Any Other™, PFC are the best brakes on the market. Known around the globe in the Sports Car market, we know It’s Quicker. PFC is involved with numerous Sports Car events across the globe, including: IMSA Continental Tire Sports car Challenge  Porsche Cup Racing Pirelli World Challenge With over 35 years of friction knowledge, and on-track experience, our process enables us to provide you with the proper friction every time. NO COMPROMISES™ All PFC pad compounds have been thoroughly processed and are “Race Ready”. This means very easy burnishing to bed pads and discs.  PFC 331 Compound 331 is the next generation of PFC endurance material. Improved control with ABS, and gentle on discs.  The 331 Carbon Metallic ® compound has been developed with higher initial bite than PFC’s renowned 08 endurance compound.  The 331 has improved release, and continues to offer exceptional control and feel. It boasts low wear rate and exceptional disc conditioning. PFC 13 Compound The new generation of ultimate high bite-high friction. Performance Friction's 13 compound has been developed with increased bite, modulation, with superior disc conditioning and release characteristics for exceptional control. Ultra-smooth and great for tracks with high grip or high downforce cars. It is the ultimate combination of high bite and infinite control. Ideal use where high bite in the first third of the stop is desired. 13’s wear is on a par with PFC’s legendary 01 compound and will operate at higher temperatures if called to. 13 has a very high threshold for fade resistance. Out of all the high bite, high torque pads on the market 13 has shown to have one of the lowest taper wear in a properly designed race caliper. PFC 11 COMPOUND This is an updated PFC part number. Previous part number was 7721.11.17.44. A new generation sprint and medium-distance friction compound, giving you the ultimate in control with superior disc conditioning. Developed from the PFC 01 compound with improved bite, modulation, and release characteristics. The PFC 11 is ultra-smooth, developed to reduce wheel locking at the end of braking while giving more cold and hot bite than the endurance-oriented PFC 08 compound. FITMENT (Iron Rotors Only): Porsche 911 991 GT3 inc RS 2014 - 2019 Front Porsche 911 991 Turbo / Turbo S 2013 - 2019 Front Porsche 911 991.2 3.0 Carrera GTS 2017 - 2019 Front Porsche 911 991.2 3.0 Carrera S 2015 - 2019 Front Porsche 911 992 3.0 Carrera S & 4S 2020 -  Front Porsche 911 992 GT3 2022 -  Front Porsche 911 992 Speedster 2019 - 2022 Front Porsche Cayman 981 GT4 2015 - 2019 Front Porsche Cayman 982 GT4 2020 -  Front

PFC Brake Pads 7727.xx.18.44 PFC Brakes offers a wide range of sports car applications. Each PFC product is meticulously created to the highest performance and technology expectations. For PFC, we take pride in the accomplishments of the drivers and race teams that run our product. With More Championships than Any Other™, PFC are the best brakes on the market. Known around the globe in the Sports Car market, we know It’s Quicker. PFC is involved with numerous Sports Car events across the globe, including: IMSA Continental Tire Sports car Challenge  Porsche Cup Racing Pirelli World Challenge With over 35 years of friction knowledge, and on-track experience, our process enables us to provide you with the proper friction every time. NO COMPROMISES™ All PFC pad compounds have been thoroughly processed and are “Race Ready”. This means very easy burnishing to bed pads and discs.  PFC 332 Compound 332 has been formulated with lower bite and torque for rear applications.  With smooth release, the 332 offers excellent stability and control.  The 332 has been designed to work with ABS applications, and has exceptionally low wear rates. PFC 11 COMPOUND A new generation sprint and medium-distance friction compound, giving you the ultimate in control with superior disc conditioning. Developed from PFC 01 compound with improved bite, modulation, and release characteristics. It is ultra smooth, developed to reduce wheel locking at the end of braking while giving more cold and hot bite than the endurance oriented PFC 08 compound. FITMENT (Iron Rotors Only) Porsche 911 991 GT3 RS 2016 - 2019 Rear Porsche 911 991 Speedster 2019 - 2021 Rear Porsche 911 991 Turbo / Turbo S 2013 - 2019 Rear Porsche 911 991 GT3 2014 - 2019 Rear Porsche 911 992 GT3 2022 -  Rear Porsche 911 992 Turbo 2019 -  Rear Porsche 918 Spyder 2013 - 2016 Rear Porsche Cayman 981 GT4 2015 - 2019 Rear Porsche Cayman 982 GT4 2019 -  Rear

Fits These Vehicles: Make Model Build (Year) Front Rear Porsche 918 Spyder 2013 +   X Porsche 991 GT3 [ceramic brakes] 2013 +   X Porsche 991 GT3 [iron brakes] 2013 +   X Porsche 991 GT3 RS [ceramic brakes] 2015 +   X Porsche 991 GT3 RS [iron brakes] 2015 +   X Porsche 991 Turbo [ceramic brakes] 2013 +   X Porsche 991 Turbo [iron brakes] 2013 +   X Porsche Cayman GT4 2016 +   X Porsche Cayman GT4 [ceramic brakes] 2016 +   X RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface RST 1: PAGID RST1 is a high average friction, aggressive pad with instant pedal response, quick release, a firm pedal at all temperatures, and a progressive torque curve. Suitable for applications with high down-force and/or very high grip. 

Girodisc Brake Pad Spreader This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.

Fits These Vehicles Make Model Build (Year) Front Rear Porsche 918 Spyder 2013 + X   Porsche 991 GT3 [ceramic brakes] 2013 + X   Porsche 991 GT3 RS [ceramic brakes] 2015 + X   Porsche 991 Turbo [ceramic brakes] 2013 + X   Porsche Cayman GT4 [ceramic brakes] 2016 + X   RSL 29: The PAGID RS29 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RS29 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear. RSC 1: The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.

FITS PORSCHE 911 GT3/GT3RS/GT2RS (2014+) FRONT WITH STEEL BRAKES The Girodisc system is a direct replacement for the OE disc on the 991 GT3, GT3RS, and GT2RS with OEM iron rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight, high performance replacements -- as opposed to a big brake kit -- your factory brake bias and ABS efficiency are preserved.The central hat section of our rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The rotor is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to their own specifications and cadmium plated for long-lasting corrosion resistance. These pins take the load from braking while maintaining the axial and radial float between the hat and disc. The pins are secured by Class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion, eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed.When used with Pagid or PFC racing brake pads and hi-temp RF1 racing brake fluid, you have what amounts to a truly amazing solution to overheating or warping rotors.If your car same with OEM center lock wheels please select the center lock drive pin option.Sold/priced in pairs.

RT RE10*:RE10 is the ultimate endurance race compound offering a balance of excellent stopping power, low thermal conductivity, extremely low pad and disc wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms *Denotes a "race only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges so it is important to choose the desired compound for the correct environment the vehicle will be used in. Pad Compounds are run on a brake dynamometer over multiple brake applications (stops) to test the materials in a controlled environment for the most accurate data. Wear rates and temperatures can be influenced by car setup, grip levels, track layout/configuration and many other variables.

RT RE10*:RE10 is the ultimate endurance race compound offering a balance of excellent stopping power, low thermal conductivity, extremely low pad and disc wear. Utilizing the latest friction material technology, RE10 offers consistent performance under the most demanding of environments. Typical Applications: Professional Endurance Racing, Club Racing, and HPDE on high demand brake platforms *Denotes a "race only" pad. Running a "racing use only" pad on the street could produce excessive noise and dust. Disc wear could be accelerated if driven at cold temperatures or used in the incorrect temperature range. Racing pads are designed to work in specific temperature ranges so it is important to choose the desired compound for the correct environment the vehicle will be used in. Pad Compounds are run on a brake dynamometer over multiple brake applications (stops) to test the materials in a controlled environment for the most accurate data. Wear rates and temperatures can be influenced by car setup, grip levels, track layout/configuration and many other variables.

FITS PORSCHE 911 GT3& GT3RS / GT2RS (2014+) REAR WITH STEEL BRAKES The Girodisc system is a direct replacement for the OE disc on the 991 GT3, GT3RS, and GT2RS with OEM iron rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The central hat section of the Girodisc rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from their own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc. The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to their own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The pins are secured by class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads. Once the Girodisc system is in place, simply replace the cast iron rotor when needed. When used with Pagid or PFC racing brake pads and hi-temp RF1 racing brake fluid, you have what amounts to a truly amazing solution to overheating or warping rotors. If your car came with OEM center lock wheels please select the center lock drive pin option. Sold/priced in pairs.

FITS PORSCHE 991 GT3, GT3RS, GT2RS (2014+) WITH PCCB BRAKES This 390mm Girodisc conversion system is a rear rotor direct replacement for the Porsche 991 GT3, GT3RS, and GT2RS originally equipped with PCCB brakes. These two-piece floating rotors will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight, high-performance Girodisc rotors (paired with the A1-154 front rotors), your factory brake bias and ABS efficiency are maintained. The low rotational and unsprung weight allows for quicker acceleration and transient suspension response. Most racers replace the factory PCCBs with steel two-piece rotors to avoid the inevitable damage to the fragile carbon ceramic discs when swapping wheels at the track! When used with Pagid or PFC performance brake pads and Discovery Parts RF1 Racing brake fluid, you have an amazing, durable solution to cracked or broken carbon-ceramic rotors at a fraction of the cost of replacing the factory PCCB units. The central hat section of each disc is made from 6061-T6 aircraft aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved-vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes eight to ten high-strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. These alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

PORSCHE 991 GT3, GT3RS, AND GT2RS (2014 +) WITH PCCB BRAKES This 410mm Girodisc conversion system is a direct FRONT rotor replacement for the Porsche 991 and 991.2 GT3, GT3RS, AND GT2RS originally equipped with PCCB brakes. These two-piece floating rotors will bolt directly to the car and work with OEM calipers perfectly. You must use must use the pad shape used on the 991 GT3 with iron rotors. The annulus (pad swept height) of these rotors is smaller than the PCCBs to keep rotor weight low and allow far better pad selection. By upgrading your brakes with lightweight high-performance Girodisc rotors (paired with Girodisc A2-154 rear rotors), your factory brake bias and ABS efficiency are maintained. The low rotational and unsprung weight allows for quicker acceleration and transient suspension response. Most racers replace the factory PCCBs with steel two-piece rotors to avoid the inevitable damage to the fragile carbon ceramic discs when swapping wheels at the track! When used with Pagid 4924 or PFC racing brake pads and Discovery Parts RF1 Racing brake fluid, you have an amazing, durable solution to cracked or broken carbon-ceramic rotors at a fraction of the cost of the factory PCCBs. The hat of each rotor is machined from 6061-T6 aircraft aluminum. The disc is manufactured from cast iron using the same specs and materials as professional racing organizations. The curved-vane design acts as a centrifugal pump to force cool air through the disc. The disc and hat mount together using a floating mount system with high-strength alloy steel drive pins and Grade 12 cap screws. The drive pins transfer braking load while maintaining axial and radial float between the disc and hat to accomodate heat expansion. Hardened washers and anti-noise springs eliminate the rattle and noise sometimes associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement (using Girodisc D1-154); the aluminum hats are re-usable. Sold/priced per pair