Ford Brake Rotors

The Girodisc system for the 2015-2018 Ford Shelby GT350 and GT350R is a direct replacement for the OE front discs; no modifications are necessary. The rotors will bolt directly to your car and work flawlessly with OE calipers. By upgrading your brakes with lightweight, high performance two-piece rotors, as opposed to a big brake kit, your factory brake bias is maintained as well as your ABS effectiveness and efficiency. Together with our customers, we have thousands of track miles on Girodisc rotors on every conceivable car. They are the go-to rotor for any of our track- or race-car builds.The central hat section of the Girodisc A1-162 rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's proprietary cast iron, poured in the USA and machined from start to finish in-house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 10 high-strength alloy steel drive pins, manufactured by Girodisc in the USA to their specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking action while maintaining the axial and radial float between the hat and disc. The pins are secured by Grade-12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads. Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed.Sold/priced per pair.

The Girodisc system for the 2015+ Ford Shelby GT350 and GT350R is a direct replacement for the OE rear discs; no modifications are necessary. The rotors will bolt directly to your car and work flawlessly with OE calipers. By upgrading your brakes with lightweight, high performance two-piece rotors, as opposed to a big brake kit, your factory brake bias is maintained as well as your ABS effectiveness and efficiency. Together with our customers, we have thousands of track miles on Girodisc rotors on every conceivable car. They are the go-to rotor for any of our track- or race-car builds.The central hat section of the Girodisc A2-162 rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's proprietary cast iron, poured in the USA and machined from start to finish in-house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 10 high-strength alloy steel drive pins, manufactured by Girodisc in the USA to their specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking action while maintaining the axial and radial float between the hat and disc. The pins are secured by Grade-12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads. Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed.Sold/priced per pair.

FITMENT (FRONT): Ford S550 Mustang GT (with Performance Pack) Discovery Parts is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. This set of 380mm x 34mm rotors is for use with the S550 Mustang GT with the optional performance package six-piston Brembo calipers. This Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs. The Girodisc floating rotors will bolt directly to your Mustang and work flawlessly with OEM calipers. By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency. The Girodisc rotors are lighter than OEM pieces, resutling in a reduction in rotational and unsprung weight (over four pounds per corner) allowing for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

FITS: Ford Focus RS The Girodisc system for the Ford Focus RS is a direct replacement for the OE front discs; no modifications are necessary. The rotors will bolt directly to your car and work flawlessly with OE calipers. By upgrading your brakes with lightweight, high performance two-piece rotors, as opposed to a big brake kit, your factory brake bias is maintained as well as your ABS effectiveness and efficiency. Together with our customers, we have thousands of track miles on Girodisc rotors on every conceivable car. They are the go-to rotor for any of our track- or race-car builds.The central hat section of the Girodisc A1-169 rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's proprietary cast iron, poured in the USA and machined from start to finish in-house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc. The rotor and hat have a floating mount system, which utilizes 10 high-strength alloy steel drive pins, manufactured by Girodisc in the USA to their specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking action while maintaining the axial and radial float between the hat and disc. The pins are secured by Grade-12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads. Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed.Sold/priced per pair.

FITMENT (REAR): Ford GT Discovery Parts is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. This Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs. The Girodisc floating rotors will bolt directly to your Mustang and work flawlessly with OEM calipers. By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency. These 20-lb. Girodisc rotors are lighter than OEM pieces, resulting in a reduction in rotational and unsprung weight allowing for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

Discovery Parts is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits Ford GT This Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs. The Girodisc floating rotors will bolt directly to your Mustang and work flawlessly with OEM calipers. By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency. These 20-lb. Girodisc rotors are lighter than OEM pieces, resulting in a reduction in rotational and unsprung weight allowing for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

FITMENT (FRONT): Ford Mustang FR500S Discovery Parts is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. This Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs. The Girodisc floating rotors will bolt directly to your Mustang and work flawlessly with OEM calipers. By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency. The Girodisc rotors are lighter than OEM pieces, resuutling in a reduction in rotational and unsprung weight (4 lbs per corner) allowing for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

FITMENT (REAR): Ford Shelby GT500 (2007-12) Ford Mustang BOSS 302(S) Ford Mustang GT (2011-14 w/ Brembo calipers) Discovery Parts is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. This Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs. The Girodisc floating rotors will bolt directly to your Mustang and work flawlessly with OEM calipers. By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency. The Girodisc rotors are lighter than OEM pieces, resuutling in a reduction in rotational and unsprung weight (4 lbs per corner) allowing for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

FITMENT (FRONT): Ford Shelby GT500 (2007-12) Ford Mustang BOSS 302(S) Ford Mustang GT (2011-14 w/ Brembo calipers) Discovery Parts is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. This Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs. The Girodisc floating rotors will bolt directly to your Mustang and work flawlessly with OEM calipers. By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency. The Girodisc rotors are lighter than OEM pieces, resuutling in a reduction in rotational and unsprung weight (4 lbs per corner) allowing for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA, made to the same specification with the same material used by professional racing organizations. The rotors' curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade-12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

FITS: 2013-2014 FORD MUSTANG GT500 (380mm rotors) Discovery Parts is an authorized dealer for Girodisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. The Girodisc system is an upgrade to a two-piece steel rotor and aluminum hat combination as a direct replacement for the OEM brake discs. The two-piece floating rotors will bolt directly to the GT500 and work flawlessly with OEM calipers. By upgrading your brakes with these lightweight high-performance replacements, as opposed to a big brake kit, your factory bias is maintained as well as your ABS effectiveness and efficiency. Girodisc rotors are lighter than OEM pieces; this reduction in rotational and unsprung weight (eight pounds per corner!) allows for quicker acceleration, stronger braking, and faster suspension response. When used with Pagid racing brake pads and Discovery Parts RF-1 racing brake fluid, you have the best possible solution to overheating, cracking, and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes ten high-strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.