All

FITS PORSCHE 991 GT3, GT3RS, GT2RS (2014+) WITH PCCB BRAKES This 390mm Girodisc conversion system is a rear rotor direct replacement for the Porsche 991 GT3, GT3RS, and GT2RS originally equipped with PCCB brakes. These two-piece floating rotors will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight, high-performance Girodisc rotors (paired with the A1-154 front rotors), your factory brake bias and ABS efficiency are maintained. The low rotational and unsprung weight allows for quicker acceleration and transient suspension response. Most racers replace the factory PCCBs with steel two-piece rotors to avoid the inevitable damage to the fragile carbon ceramic discs when swapping wheels at the track! When used with Pagid or PFC performance brake pads and Discovery Parts RF1 Racing brake fluid, you have an amazing, durable solution to cracked or broken carbon-ceramic rotors at a fraction of the cost of replacing the factory PCCB units. The central hat section of each disc is made from 6061-T6 aircraft aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved-vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes eight to ten high-strength alloy steel drive pins manufactured by Girodisc in the USA to their own specifications and are cadmium plated for corrosion resistance. These alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/priced per pair.

PORSCHE 991 GT3, GT3RS, AND GT2RS (2014 +) WITH PCCB BRAKES This 410mm Girodisc conversion system is a direct FRONT rotor replacement for the Porsche 991 and 991.2 GT3, GT3RS, AND GT2RS originally equipped with PCCB brakes. These two-piece floating rotors will bolt directly to the car and work with OEM calipers perfectly. You must use must use the pad shape used on the 991 GT3 with iron rotors. The annulus (pad swept height) of these rotors is smaller than the PCCBs to keep rotor weight low and allow far better pad selection. By upgrading your brakes with lightweight high-performance Girodisc rotors (paired with Girodisc A2-154 rear rotors), your factory brake bias and ABS efficiency are maintained. The low rotational and unsprung weight allows for quicker acceleration and transient suspension response. Most racers replace the factory PCCBs with steel two-piece rotors to avoid the inevitable damage to the fragile carbon ceramic discs when swapping wheels at the track! When used with Pagid 4924 or PFC racing brake pads and Discovery Parts RF1 Racing brake fluid, you have an amazing, durable solution to cracked or broken carbon-ceramic rotors at a fraction of the cost of the factory PCCBs. The hat of each rotor is machined from 6061-T6 aircraft aluminum. The disc is manufactured from cast iron using the same specs and materials as professional racing organizations. The curved-vane design acts as a centrifugal pump to force cool air through the disc. The disc and hat mount together using a floating mount system with high-strength alloy steel drive pins and Grade 12 cap screws. The drive pins transfer braking load while maintaining axial and radial float between the disc and hat to accomodate heat expansion. Hardened washers and anti-noise springs eliminate the rattle and noise sometimes associated with floating rotors. The two-piece Girodisc design allows for disc-only replacement (using Girodisc D1-154); the aluminum hats are re-usable. Sold/priced per pair

Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits Ferrari 458 Italia Fits Ferrari 488 Fits Ferrari F8 Fits Ferrari Pista The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

FITS: Ferrari 430 SCUDERIA Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

Discovery Parts is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline. Fits Ferrari 430 Challenge The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response. When used with Pagid or PFC performance brake pads, and Discovery Parts RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors. The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc. The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors. The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling. Sold/Priced per pair.

Call us any time at 888-748-7223 for Discovery Parts-Exclusive Forgeline pricing you won't find anywhere else! Discovery Parts offers FREE SHIPPING on all Forgeline Wheel Orders! FORGELINE VX1R (FIVE-LUG) Contact a wheel specialist today at 888-748-7223 to discuss the details of your custom Forgeline wheel build. We can guide you through sizing, offsets, finishes, and other details to make sure your Forgelines are perfectly suited to your needs! If you like the look of our popular VX1, but need a load rating that is suitable for dedicated track duty, then the VX1R was engineered for you! The VX1R is a fully track-ready competition wheel equal in weight and strength to Forgeline's famous GA1R and GS1R Competition Series wheels.The VX1R features a sharp Y-spoke design, with long spokes that wrap around the lug holes, striking sharp angles, a deep concave profile, and a chamfered outer edge. The Forgeline VX1R is a fully-forged, one-piece monoblock wheel utilizing manufacturing technology similar to the very successful GA1R. Beyond just beautiful style, the VX1R is engineered to allow plenty of room for caliper clearance and extreme brake fitment. Forgeline's computer-simulated FEA design process yield a wheel that is lightweight and stiff, with excellent fatigue strength.Currently available in 18, 19, 20, and 21-inch diameters with a range of widths and offsets, the VX1R can be made to accommodate most five-lug or center lock applications. And just like any Forgeline wheel, the VX1R is available with fully customizable finish options! FEATURES: One-Piece Forged Monoblock Construction Concave Profile Sharp Y-Spoke Design Striking Sharp Angles Strong Chamfered Machining Details Lightweight Load Rated for Motorsport Applications Generous Brake Clearance Forged 6061-T6 Aluminum Includes Aluminum Center Cap Customizable Finish Options Legendary Forgeline Quality

Call us any time at 888-748-7223 for Discovery Parts-Exclusive Forgeline pricing you won't find anywhere else! Discovery Parts offers FREE SHIPPING on all Forgeline Wheel Orders! FORGELINE GT1 (CENTER LOCK) Contact a wheel specialist today at 888-748-7223 to discuss the details of your custom Forgeline wheel build. We can guide you through sizing, offsets, finishes, and other details to make sure your Forgelines are perfectly suited to your needs! FITS PORSCHE CENTER LOCK Derived from the Forgeline GTD1 racing wheel, the GT1 brings racing DNA to the street. The GT1 represents the latest in advanced wheel technology -- including one-piece forged monoblock construction, motorsport engineered design, I-beamed spokes and spoke spans -- to deliver head-turning good looks with track-ready capability! The Forgeline GT1 is a fully-forged one-piece monoblock wheel. Utilizing manufacturing technology similar to the very successful GA1R wheel, the concave 12-spoke design of the GT1 looks great and allows plenty of room for caliper clearance and extreme brake fitment. Forgeline's computer-simulated FEA design process yields a wheel that is very lightweight and extremely stiff, with excellent fatigue strength. The GT1 is engineered exclusively for Porsche center lock applications and fits all Porsche center lock systems for street and track, including Cup Car and RSR applications. Currently available in 18, 19, 20, and 21-inch diameters, we'll have your GT1 made in your choice hundreds of customizable finish options! FEATURES: One-Piece Monoblock Construction Concave Profile 12-Spoke Design Engineered for Porsche Center Lock Fitments I-Beamed Spoke Technology I-Beamed Spoke Spans Along the Lip Very Lightweight, Stiff, and Strong Generous Brake Clearance Forged 6061-T6 Aluminum Fits All Porsche Center Lock Systems for Street and Track, Including Cup Car and RSR Applications Customizable Finish Options Legendary Forgeline Quality

Bell MAG-10 Rally Carbon Fiber Auto Racing Helmet   Introducing the Bell MAG-10 Rally Carbon Fiber Helmet: Where Vintage Meets Velocity! Hey speedsters, whether you're tearing up the track or just appreciating the beauty of engineering, you've met your match with the Bell MAG-10 Rally Carbon Fiber Helmet. Drawing on the legendary HP10 Rally as its muse, it's a nod to heritage combined with a salute to innovation. Features to Flaunt: Ultra-Light & Uber Strong: We're talking premium carbon composite shell. It’s like donning a nimble yet protective exoskeleton. Quick Emergency Response: A Fast Removable Carbon Half Chin Bar (HCB) ensures rapid access in emergencies. We care for your noggin. Visionary Visibility: With an adjustable carbon sun peak and an integrated anti-scratch dark smoked sunscreen, it's the epitome of seeing and being seen. Clarity is Key: ZeroNoise® tech, impeccable speakers, and a noise-canceling microphone ensure you're heard, even when your ride is screaming. Plug and Play: A versatile In-Molded Female Nexus Connector makes compatibility a breeze. Safety-First: Thanks to those ever-reliable, factory-installed Hans anchors. Tailored Comfort: Dive into an array of interior fabric colors. Express yourself; you've earned it. Now, picture this: the roar of engines, the smell of rubber and oil, and you, decked out in this premium piece of engineering. As you zoom past, it's not just about the speed; it's about making a statement. So, why wait? Elevate your racing ensemble with the Bell MAG-10 Rally Carbon Fiber Helmet. Order Yours Now, and let every lap be a victory lap! Drawing inspiration from the HP10 Rally, the MAG-10 RALLY CARBON stands out as a top-tier, ultra-lightweight rally helmet with a contemporary design. Crafted with a feather-light carbon composite shell, it boasts features like a quick-detach Half Chin Bar (HCB), adjustable carbon peak, and a new integrated sunscreen. Prioritizing comfort, sound insulation, and a professional fit, this helmet is the preferred choice for rally professionals seeking premium quality. With insights from the HP10's extensive R&D, the MAG-10 RALLY CARBON redefines excellence in the Premium Helmet segment. Integrated with ZeroNoise® technology, powerful speakers, and a noise-canceling microphone, it promises unparalleled safety, comfort, and communication efficiency. BELL MAG-10 RALLY CARBON FIBER HEMET DETAILS: Open face helmet featuring ultra-lightweight Premium carbon composite shell Fast Removable Carbon Half Chin Bar (HCB) quickly and easily detachable to ensure fast access to breathing ways without the need to remove the helmet in case of emergency Advanced multi-density, multi-piece liner to maximize energy absorption and impact performance Adjustable carbon sun peak Adjustable integrated anti-scratch dark smoked sunscreen Integrated cheek pads with multi densities advanced materials for optimal comfort Flexible yet sound insulating integrated ear muffs for comfort combined with sound insulation ZeroNoise® electronics, high power (yet lightweight) speakers and efficient noise cancelling microphone. Ultra-reliable heavy duty In-Molded Female Nexus Connector (compatible with other brands of amplifiers) Detachable right side-cover for smooth integration of the Female Nexus Connector Flat right side cover supplied in the box, for those who prefer using a straight cable coming out of the helmet instead of the integrated connector Factory installed Hans anchors as original equipment Interior: Dark Grey High Strength – High Comfort FR Fabric Alternative interior fabric colors: Tan, White, Red, Purple, Blue, Green and Neon Yellow (by special order). Adjustable sunscreens available as accessories in various colors and TWO lengths to ensure optimal visual comfort Color: Carbon, Gloss finish Sizes: 54-55-56-57-58-59-60-61-61+ CM BELL MAG-10 RALLY CARBON FIBER HELMET FREQUENTLY ASKED QUESTIONS (FAQ): Remember that safety is paramount in auto racing, and choosing the right helmet and maintaining it properly is essential for your protection on the track. Always consult with the professionals at Discovery Parts and refer to the manufacturer's guidelines for specific questions about your racing helmet. Why do I need a racing helmet? Auto racing helmets are designed to protect drivers from head injuries and fire during high-speed races and crashes. They are a crucial safety component in motorsports. How do I choose the right size Bell MAG-10 Rally Carbon Fiber helmet? You should measure your head's circumference using a flexible tape measure, then refer to the manufacturer's sizing chart to select the appropriate size helmet. Please review our blog posting on how to properly fit your new auto racing helmet from Discovery Parts. What safety standards should I look for in a Bell MAG-10 Rally Carbon Fiber racing helmet? Look for helmets that meet safety standards like Snell and FIA depending on your racing discipline. These standards ensure the helmet's safety and quality. DOT helmets are designed for street use and not for racing and track use. What's the difference between full-face and open-face, and helmets? Full-face helmets provide the most protection with a complete face shield, while open-face helmets cover the top and sides of the head. Can I use a motorcycle helmet for auto racing? No, motorcycle helmets do not provide the same level of protection as auto racing helmets, as they are designed for different purposes. It's recommended to use a helmet specifically designed for auto racing which includes fire protection in addition to impact protection. How often should I replace my Bell MAG-10 Rally Carbon Fiber auto racing helmet? Auto racing helmets should be replaced every 5-10 years, depending on the manufacturer's recommendations and usage. If the helmet is involved in a crash, it should be replaced immediately. Are expensive racing helmets safer than budget ones? Safety standards dictate the minimum safety requirements, so even budget-friendly helmets can offer protection. However it’s important to consider how lower-priced helmets are meeting the required testing standards. More expensive helmets are lighter, smaller, are constructed of superior materials, and often come with additional features then less expensive helmets. How do I maintain and clean my Bell MAG-10 Rally Carbon Fiber racing helmet? Follow the manufacturer's instructions for cleaning and maintenance. You should clean the exterior, interior and shield with the Molecule Helmet Care Kit. Do I need to wear a balaclava under my Bell MAG-10 Rally Carbon Fiber racing helmet? Balaclavas are typically not required for Driver's Education events, however they make wearing a helmet much, much more comfortable. Balaclavas will provide fire protection (if fire rated), help keep your helmet lining clean and order free by absorbing the majority of sweat while using it, and additionally balaclavas make putting your helmet on and taking it off by protecting your ears and keeping from from folding over when you helmet is worn. Discovery Parts recommends balaclavas from Alpinestars, OMP, Sabelt, Sparco, and Stand21. If you are entering sanctioned auto racing events, balaclavas will be required for fire protection. Is the SNELL SA Rating important? The Snell SA2020 certification is a safety standard established by the Snell Memorial Foundation for auto racing helmets. It sets the criteria and requirements that helmets must meet to be considered safe and suitable for use in motorsport events. Snell SA2020 certification is highly regarded in the motorsports industry and is often required or recommended by racing organizations and events. It signifies that a helmet has passed rigorous testing to provide maximum safety for drivers in various motorsport disciplines, including road racing, NASCAR, Formula 1, drag racing, and more. It's essential for drivers to check the specific safety standards required by the racing organizations they participate in to ensure compliance. Is the FIA helmet certification important? Yes, FIA (Fédération Internationale de l'Automobile) certification is crucial for auto racing helmets, especially in the context of international motorsport events and many national and regional racing series in the USA. The FIA 8859-2015 standard is commonly associated with racing helmets used in various motorsport disciplines. Helmets certified to FIA 8859-2015 met the safety requirements set by the FIA and were widely accepted in many racing series Which helmet certification is the most stringent and the hardest to meet? The FIA 8860-2018 certification is considered the most stringent and advanced helmet certifications available for auto racing helmets, and it is often associated with top-tier motorsport categories like Formula 1. It's important to note that the FIA 8860-2018 helmets offer a high level of protection and their use is mandatory in many racing series. Drivers should always check the regulations of the racing series they intend to participate in to ensure compliance with helmet certification standards. Can I wear glasses with my Bell MAG-10 Rally Carbon Fiber helmet? Most helmets have provisions for wearing glasses or goggles, but check the design to be sure. Most manufacturers feature helmet models with wider eye ports to better accommodate eye glasses. Are carbon fiber helmets better? Carbon fiber helmets are lightweight and strong, a top choice for racers. But remember, certification matters most. Can I use a used helmet for racing? It's best to buy a new helmet. Used helmets may have unseen damage or be out of date on safety standards. Can I buy replacement parts for my helmet, like visors or padding? Many manufacturers offer replacement parts, including visors and padding, to extend your helmet's lifespan. How can I prevent helmet fogging during races? Anti-fog sprays and inserts are available to help keep your visor clear during races. What's the importance of proper helmet ventilation? Proper ventilation helps keep you cool and comfortable during races, reducing the risk of heat exhaustion. How do I store my Bell MAG-10 Rally Carbon Fiber helmet between races? Keep it in a cool, dry place away from direct sunlight and chemicals in a bag designed to store your auto racing helmet, like the Discovery Parts Evo Helmet Bag. Where can I buy a certified racing helmet? You should only buy from a professional authorized dealer who has sold thousands of helmets. You can find all the best brands at Discovery Parts online at www.discoveryparts.com or visit our retail store at Atlanta Motorsports park or at one of the hundreds of race and track day events we attend and support. Remember, safety should always come first in auto racing. Choose a certified helmet that meets the necessary standards to protect yourself on the track. Frequently Asked Questions About Bell Helmets: Where are Bell helmets made? Bell helmets are proudly manufactured in the Bahrain, maintaining the highest quality standards. Is Bell a good helmet brand? Yes, Bell is renowned for its commitment to safety, innovation, and performance, making it a trusted choice among professional racers and enthusiasts. Are Bell helmets Snell approved? Yes, many Bell helmets are Snell approved, meeting rigorous safety standards. Are Bell helmets FIA approved? Absolutely, several Bell helmets are FIA 8860-2018 certified, ensuring they meet the most stringent safety requirements. Do Bell helmets run small? Bell offers a variety of sizes and often provides sizing charts to help you choose the right fit. It's important to measure your head and refer to their guidelines for a proper fit. For racers who demand the best in safety and performance, Bell auto racing helmets are the ultimate choice. Explore our extensive collection to find the perfect helmet for your racing needs. Bell Racing Helmets: Bell Racing Helmets are renowned for their exceptional quality and safety features. With a wide range of models to choose from, you can find the perfect Bell Racing Helmet to suit your racing needs. Bell Racing Helmet: Each Bell Racing Helmet is a product of meticulous craftsmanship and cutting-edge technology. When you wear a Bell Racing Helmet, you're choosing a helmet that prioritizes your safety and performance on the track. Bell Race Helmets: Bell Race Helmets come in various styles and designs to cater to different types of motorsports. Whether you're into karting, open-wheel racing, or stock car racing, Bell has race helmets tailored for your specific discipline. Bell Race Helmet: Your Bell Race Helmet is more than just protective gear; it's a crucial part of your racing ensemble. The aerodynamic design of a Bell Race Helmet helps reduce wind resistance, giving you a competitive edge. Bell Helmet: A Bell Helmet is a symbol of trust in motorsports. Professional racers and amateurs alike rely on the comfort, safety, and durability that Bell Helmets provide during intense racing conditions. Bell Helmets: Bell Helmets have a rich history of innovation and excellence. The extensive range of Bell Helmets ensures that there's a model suitable for every racer, whether you're a seasoned pro or just starting in the sport. Bell Carbon Fiber Helmet: Bell Carbon Fiber Helmets combine the lightweight properties of carbon fiber with advanced safety features. These helmets are a top choice for racers seeking the ultimate in protection without sacrificing comfort. Race Car Helmet: A race car helmet is a fundamental piece of safety gear for any racer. Bell's race car helmets are engineered to meet the rigorous demands of motorsports, ensuring you stay safe on the track. Racing Helmet: Your racing helmet is your shield against potential accidents. Bell Racing Helmets are designed to offer superior impact protection while maintaining optimal visibility and ventilation. Racing Helmets: Racing helmets are a racer's best friend. Bell Racing Helmets, with their reputation for quality and safety, are the go-to choice for many professionals and enthusiasts in the racing community. Bell Racing: Bell Racing is synonymous with excellence in the motorsports industry. Their commitment to research, development, and testing has solidified their position as a leader in racing helmet technology. Auto Racing Helmet: When it comes to auto racing, your helmet is your first line of defense. Bell Auto Racing Helmets are engineered to withstand the rigors of high-speed racing, ensuring your head is protected. Auto Racing Helmets: Auto racing helmets from Bell are designed to provide optimal head protection while maintaining lightweight and aerodynamic qualities, allowing you to perform at your best.

AiM Sports SmartyCam 3 GP The AiM SmartyCam 3 GP motorsports video camera has been designed specifically for racing with two purposes in mind: provide great videos, and supply you with all the information and data you need. The AiM SmartyCam 3 GP camera overlays any data you want from both GPS and AiM data-loggers connected to your ECU. Full HD camera system, Video output, CAN connection, USB-C connection, and GPS port are only a few of the features of SmartyCam 3 GP: the power of simplicity. Video recording format: H.264, 1920x1080 pixels @ 60 FPS Display resolution: 2.4" (240 x 320 pixels) Lens: low distortion camera lens CMOS sensor: Global Shutter Field of view: 67°, 84°, or 120° Internal battery: rechargeable lithium-ion Video Out: 3G-SDI External power: 9V to 15V Supports SD card: up to 2TB Connectors: Binder 712 female connectors (2), SMA female connector (1), USB-C (1) Usage temperatures: -10°C to +50°C (14ºF to 122ºF) Auto Power ON: Yes Auto Power OFF: Yes Auto Start/Stop Recording: Yes Body: anodized aluminium Dimensions: Main unit 120.8 x 80.2 x 30.9mm | Bullet camera 24mm diam x 46mm (120° lens) | Bullet camera 24mm diam x 41 mm (67° or 84° lens) Bullet Cable Length: seven different lengths available from 0.5m to 4.0m  Weight: Main Body 320g; Bullet Camera 45g Waterproof: IP65

CMS Performance Roll Bar for the Mustang Dark Horse (2024+) THE BEST ROLL BAR ON EARTH IN FORD'S TRACK MONSTER The CMS Performance Roll Bar is the strongest, safest, and most beautifully constructed roll bar on the market for the Dark Horse. In designing our roll bar, safety, strength, and structural integrity were our primary goals. That's why it is fully TIG welded from ultra-strong Docol R8 Advanced High-Strength Steel sized 1.75" diam x .095" wall, vs. the mild-steel tubing other companies use. Docol R8 is 30-35% stronger than DOM mild steel and even 10-15% stronger than 4130 CrMo steel. This allows CMS Performance to design a roll bar that is stronger and lighter weight. Precision CNC machined interlocking roll bar clamps, made to our specifications in the USA, make joining the main hoop and kickers easier during installation while giving the CMS Performance roll bar a premium, finished look. Adding an optional Shrader Rear Seat Delete Kit gives your roll bar installation a from-the-factory OEM look. AMERICAN MADE SAFETY FOR AN AMERICAN ICON Let's face it, safety is the primary reason to install a roll bar in your Dark Horse. So the CMS Performance Shelby Roll Bar is designed to place your harness shoulder straps at both the proper angle (0° to -20°) and distance to the driver.  The rear kickers bolt to a strong existing bulkhead, requiring no reinforcement plates beneath the floor pan. Our use of state-of-the-art Docol ultra-high-strength-steel tubing throughout allows us to keep the driver's rear view unobstructed by diagonal braces, which also keeps weight down. Every detail is engineered with safety and structural integrity as our primary goal. PRECISION CRAFTED AND CUSTOM FINISHED IN OEM COLORS The other reason to install a roll bar is because it really complements the aggressive, race-inspired styling of the S650 Dark Horse. We're gear heads, we get that. So each bar is crafted by hand by master fabricators, 360o TIG welded for the ultimate in strength and durability, and then custom powder coated in our facility (at no extra charge). We've color-matched powder to most of Ford's factory paint colors for a truly customized look, or you can choose from thousands of custom colors and finishes like the amazing Superchrome, giving your Shelby a personalized look that will last. Going from raw Docol tube stock to a gleaming finish, every roll bar is handcrafted by our most experienced cage- and race car builders. Nothing is left to chance. The CMS roll bar is designed to give you an unobstructed view through your rear window. None of your plastic interior trim needs to be removed or cut, just a little carpet that is hidden away. So if you ever need to put your car back to stock, it will look as though the roll bar was never there. Click Here for Installation Instructions EASIER INSTALLATION & MULTIPLE OPTIONS FOR YOUR DARK HORSE ROLL BAR Check out the GREAT installation video here! 1 Complete, detailed instructions make installation pretty simple (figure about two hours if you're reasonably handy; having a buddy helps!) All the supplied installation hardware is American made: Grade 8 mounting hardware and an industrial carbide drill bit. So you don't have worry that you don't have what you need for a flawless installation. You can add six-point or four-point harnesses to your order to take full advantage of the safety upgrade your roll bar represents. The CMS Performance Sub Strap + Lap Belt Mount makes securely installing your racing harnesses easy. Check out the drop-downs above. Many customers also add CMS Locking Harness Collars to keep harness shoulder straps right where you want them (they're not required for safety, but a lot of people like the look.) 1 Note: Thank you to our customer "@1_trickpony_" for putting in the time and effort to shoot and edit a fantastic installation video! CMS PERFORMANCE S650 MUSTANG DARK HORSE ROLL BAR DETAILS Manufacturer: CMS Performance Manufacturer Part #: CPRB-S650 Material: 1.75″ x .095" Docol R8 Advanced High-Strength Steel tubing Construction: full 360o TIG welding Design: one-piece main hoop and three-piece rear kicker for simpler installation. Weight: 52 lbs. (23.6 kg) Included hardware: all necessary Grade 8 bolts, nuts & washers Drill bit: included CMS PERFORMANCE S650 MUSTANG DARK HORSE ROLL BAR FEATURES CNC-cut mounting plates. Designed, built, and finished by CMS Performance in the USA. American-made CNC machined high-strength steel interlocking clamps Allows full seat travel with any seat. Straightforward installation and perfect fitment, guaranteed. This product is intended for off-road race track use only.

Call us any time at 888-748-7223 for Discovery Parts-Exclusive Forgeline pricing you won't find anywhere else! Discovery Parts offers FREE SHIPPING on all Forgeline Wheel Orders! FORGELINE SS1R Contact a wheel specialist today at 888-748-7223 to discuss the details of your custom Forgeline wheel build. We can guide you through sizing, offsets, finishes, and other details to make sure your Forgelines are perfectly suited to your needs! Forgeline Motorsports has built our reputation from making wheels that are track-proven at the highest levels of road racing, and our SS1R motorsport wheel is certain to continue this long tradition. Derived directly from the SS1R-GT wheel (which is engineered specifically for ultra-competitive IMSA and WEC GT3 racing), the Forgeline one piece forged monoblock SS1R 5-Lug wheel is our lightest, strongest, and stiffest racing wheel made to date! FEATURES: The Forgeline SS1R wheel is a one piece forged monoblock construction meaning that the entire wheel is precision-machined from a single forging of a proprietary grade of 6061-T6 aerospace aluminum. It features a split six spoke design, I-beamed spokes, tapered outer edge, and aggressive machining details that allow it to look as good as it performs. The Forgeline SS1R 5-Lug is available in a range of widths and custom offsets in diameters ranging from 18 to 22-inches and can be finished with a wide offering of fully-customizable powder coat colors and finish options. One-Piece Forged Monoblock Construction Concave Profile Split 6-Spoke Design I-Beamed Spoke Technology Aggressive Tapered Outer Edge Very Lightweight Very Strong (2100 lb street tire load rating) Minimal Deflection Under Load Generous Brake Clearance Forged 6061-T6 Aluminum Customizable Finish Options Legendary Forgeline Quality and Customer Service

Forgeline AL307 The amazing AL307 represents an exciting revolution in Forgeline wheel design and is engineered specifically for the high-performance modern supercar. The AL307 delivers cutting-edge styling with five split-V spokes that span integrated lug holes with intricate multi-dimensional edges. Each spoke features a distinctive cutout along the spoke inner edge. These concave spokes are tapered and extend beyond the rim register to reach out over the step of the AL307 modular aluminum outer rim shell. The Forgeline AL Series AL307 is a custom made-to-order three piece modular wheel comprised of a precision-machined forged 6061-T6 aluminum center, 6061-T6 aluminum rim shells, and a 1.5-3.0 inch wide stepped-lip outer. It is available in 18, 19, 20, and 21-inch diameters and is uniquely engineered for modern exotic sport and luxury vehicle applications. And like any Forgeline wheel, the AL307 is fully customizable in fitment and finish. Custom Made-to-Order for Each Customer and Each Unique Vehicle Application Unique Center Design is Precision-Machined from Forged 6061-T6 Aluminum Five Multi-Dimensional V-Spokes Span Integrated Lug Holes Complex Machining Details Distinctive Cutouts Along the Inner Edge of Each Spoke Unique Full-Length Spokes Extend Beyond the Rim Register and Reach Over the Step of the Outer Rim Shell Available in 18, 19, 20 and 21-inch Fitments Customizable Finish Options Legendary Forgeline Quality and Customer Service

Forgeline AL306 Based upon Forgeline's original five-lug AL301, the 6-lug AL306 continues the exciting evolution in Forgeline wheel design and is engineered specifically for the high-performance 6-lug supercar. The AL306 offers cutting-edge styling with a unique precision-machined forged 6061-T6 aluminum center featuring a lightweight racing-inspired six Y-spoke forged aluminum center design with aggressive I-beam machining details. These concave spokes are tapered and extend beyond the rim register to reach out over the step of the AL306 modular aluminum outer rim shell. And it 6-lug hub center makes the AL306 perfect for the Dodge Viper or other 6-lug sport & luxury applications! The Forgeline AL Series AL306 is a custom made-to-order three piece modular wheel comprised of a precision-machined forged 6061-T6 aluminum center, 6061-T6 aluminum rim shells, and a 1.5-3.0 inch wide stepped-lip outer. It is available in 18, 19, 20, and 21-inch diameters and is uniquely engineered for modern exotic 6-lug sport and luxury vehicle applications. And like any Forgeline wheel, the AL306 is fully customizable in fitment and finish. Custom Made-to-Order for Each Customer and Each Unique Vehicle Application Unique Center Design is Precision-Machined from Forged 6061-T6 Aluminum Lightweight Racing-Inspired Six Y-Spoke Center Design Six-Lug Hub Center Aggressive I-Beam Machining Details Unique Full-Length Spokes Extend Beyond the Rim Register and Reach Over the Step of the Outer Rim Shell Available in 18, 19, 20 and 21-inch Fitments Customizable Finish Options Legendary Forgeline Quality and Customer Service

Forgeline AL305 The AL305 represents an exciting evolution in Forgeline wheel design and is engineered specifically for the high-performance modern supercar. The AL305 delivers cutting-edge styling with a high-tech precision-machined forged 6061-T6 aluminum center featuring lightweight racing-inspired ten spoke design, open-lug hub center, and aggressive I-beam machining. The Forgeline AL Series AL305 is a custom made-to-order three piece modular wheel comprised of a precision-machined forged 6061-T6 aluminum center, 6061-T6 aluminum rim shells, and a 1.5-3.0 inch wide stepped-lip outer. It is available in 18, 19, 20, and 21-inch diameters and is uniquely engineered for modern exotic sport and luxury vehicle applications. And like any Forgeline wheel, the AL305 is fully customizable in fitment and finish. Custom Made-to-Order for Each Customer and Each Unique Vehicle Application Unique Center Design is Precision-Machined from Forged 6061-T6 Aluminum Lightweight Racing-Inspired Ten Spoke Center Design Open-Lug Hub Center Aggressive I-Beam Machining Unique Full-Length Spokes Extend Beyond the Rim Register and Reach Over the Step of the Outer Rim Shell Available in 18, 19, 20 and 21-inch Fitments Customizable Finish Options Legendary Forgeline Quality and Customer Service

Forgeline AL304 The uniquely-styled AL304 represents an exciting evolution in Forgeline wheel design and is engineered specifically for the high-performance modern supercar. The AL304 delivers cutting-edge styling with a high-tech precision-machined forged 6061-T6 aluminum center featuring five Tuning Fork split spokes that span hidden lug holes. The AL304 relatively open spoke pattern works well to exhibit giant supercar brakes. The Forgeline AL Series AL304 is a custom made-to-order three piece modular wheel comprised of a precision-machined forged 6061-T6 aluminum center, 6061-T6 aluminum rim shells, and a 1.5-3.0 inch wide stepped-lip outer. It is available in 18, 19, 20, and 21-inch diameters and is uniquely engineered for modern exotic sport and luxury vehicle applications. And like any Forgeline wheel, the AL304 is fully customizable in fitment and finish. Custom Made-to-Order for Each Customer and Each Unique Vehicle Application Unique Center Design is Precision-Machined from Forged 6061-T6 Aluminum Five Tuning Fork Split Spokes Span Hidden Lug Holes Open Spoke Pattern Exhibits Giant Supercar Brakes Unique Full-Length Spokes Extend Beyond the Rim Register and Reach Over the Step of the Outer Rim Shell Available in 18, 19, 20 and 21-inch Fitments Customizable Finish Options Legendary Forgeline Quality and Customer Service

Forgeline AL303 The intricately-sculpted AL303 represents an exciting evolution in Forgeline wheel design and is engineered specifically for the high-performance modern supercar. The AL303 offers cutting-edge styling with a unique precision-machined forged 6061-T6 aluminum center featuring ten asymmetric Y-spokes grouped together in opposing pairs. These concave spokes connect far into the center, thanks to special engineering and machining deep into the edge of the mounting pad, and extend beyond the rim register to reach out over the step of the AL303 modular aluminum outer rim shell. The Forgeline AL Series AL303 is a custom made-to-order three piece modular wheel comprised of a precision-machined forged 6061-T6 aluminum center, 6061-T6 aluminum rim shells, and a 1.5-3.0 inch wide stepped-lip outer. It is available in 18, 19, 20, and 21-inch diameters and is uniquely engineered for modern exotic sport and luxury vehicle applications. And like any Forgeline wheel, the AL303 is fully customizable in fitment and finish. Custom Made-to-Order for Each Customer and Each Unique Vehicle Application Intricate Center Design is Precision-Machined from Forged 6061-T6 Aluminum Ten Asymmetric Y-Spokes are Grouped Together in Opposing Pairs Special Engineering & Machining Deep Into the Mounting Pad Creates Additional Spoke Length Unique Full-Length Spokes Extend Beyond the Rim Register and Reach Over the Step of the Outer Rim Shell Available in 18, 19, 20 and 21-inch Fitments Customizable Finish Options Legendary Forgeline Quality and Customer Service