CMS Performance

CMS Performance Clubsport Roll Bar For Porsche 991 GT3 & GT3RS This Roll Bar Fits The Following Cars: Porsche GT3, 991.1 and 991.2 (2014-2019) Porsche GT3RS, 991.1 and 991.2 (2016-2019) PENULTIMATE ROLL BAR FOR YOUR PORSCHE GT3 and GT3RS The CMS Performance Clubsport Roll Bar is a new variant of our incredibly popular GT3/GT3RS roll bar. Re-designed with steel gusseting and high-strength support tubing is added to the top and bottom of the X-brace and to all four corners, the CMS Performance Clubsport Roll Bar takes rigidity and strength to another level. This is the strongest, highest quality bolt-in roll bar on the market for the Porsche 991 GT3 and GT3RS, period. In designing and building the CMS Performance Clubsport roll bar, structural rigidity and impact protection were our primary goals. This roll bar is fully 360o TIG welded, the main tubing is 1.75" Docol R8 Advanced High-Strength Steel. CMS is the only roll bar manufacturer to employ this modern material. The support tubing is Docol R8 as well, and the gussets are machined from steel plate. CMS Performance tailors the GT3/GT3RS Clubsport roll bar to take full advantage of the strongest chassis mounting points in the Porsche 991 GT3/GT3RS . The main roll hoop is X-braced and gusseted, with a single tube cross-bar providing lateral strength that's also used for mounting racing harness shoulder straps. ATTENTION TO DETAIL IS THE HALLMARK OF CMS PERFORMANCE The cross-bar on the CMS Performance Clubsport Roll Bar for the Porsche 991 GT3 and GT3RS lets you attach your racing harness shoulder straps at the proper angle (0° to -20° front-to-back) and distance relative to the driver and passenger, regardless of seat position. The CMS Performance Clubsport Roll Bar was designed to leave your rear view unobstructed by additional bracing that other roll bars require due to the use of inferior materials. CMS Performance also features a unique three-piece rear kicker that bolts to the Porsche 991 GT3/GT3RS rear shock towers (where the factory GT3 Cup Car roll cage mounts). These are the strongest rear mounting points, and also add rigidity to the chassis for more precise handling. This kicker design is incredibly strong while also being a breeze to install (typical one-piece designs can be a nightmare to install). The main roll hoop is mounted to your Porsche's steel frame structure beneath the vehicle just like the factory Cup Car cage. BUILT LIKE A TANK, FINISHED LIKE A PORSCHE Designed using the same guidelines as a full racing roll cage and fully 360o TIG welded by our chassis fabricators and master welders, the CMS Performance Clubsport Roll Bar for the Porsche 991 GT3 and GT3RS is unsurpassed in quality, durability, and structural integrity. Each roll bar is professionally powder-coated in-house to guarantee fit and finish no other manufacturer can match. This also lets us use powder coat colors we've matched to Porsche GT3 and GT3RS OEM paint colors for a truly customized aesthetic. We also offer custom technical powder coat finishes like the amazing Superchrome! Or you can choose our rich satin black powder coat for a more low-key installation. Powder coating any color you choose is included in the price of your CMS Performance roll bar. DEMAND THE BEST FOR YOUR GT3 OR GT3RS Thoughtful engineering and design, superior materials, masterful fabrication, and beautifully customized finishing. That's the CMS Performance way of doing things. Backed by our legendary customer service, it all adds up to this: you can pay more for a roll bar, but you can only get the best from CMS. ADD PREMIUM RACING HARNESSES TO YOUR PORSCHE Add six-point Schroth Enduro 2x2 GT3, Schroth Flexi 2x2 GT3, or Sabelt Silver Series GT3 racing harness to your order and save! These harnesses are specifically designed for the Porsche 992 GT3 and GT3RS and will bolt to your factory lightweight carbon bucket seats. Or you can add four-point Schroth Profi II ASM GT3 or Sabelt Porsche GT3 4 Point harnesses, ideal for the Porsche 992 GT3 and GT3RS passenger seat that doesn't have a factory sub-strap pass through. With six-point harnesses, we strongly recommend using the CMS Performance Sub Strap Mount to provide a solid, properly located anchor for your anti-submarine straps. The CMS Performance Sub Strap Mount is simple to install at the same time you're installing your roll bar! Click Here for Installation Instructions EASY INSTALLATION TAKES THE HEADACHE OUT OF ROLL BARS We've been through more than a few wrestling matches installing bolt-in roll bars in street cars. Fortunately, we used that experience to design the CMS Performance Roll Bar for the Porsche 992 GT3 and GT3RS to be a lot less frustrating to install. We hesitate to go so far as to say it's easy, but we'll say it isn't hard if you have a friend and some basic tools. CMS PERFORMANCE PORSCHE CLUBSPORT ROLL BAR DETAILS: Manufacturer: CMS Performance Manufacturer Part: CPRB-991CS Materials: Docol R8 Advanced High-Strength Steel; steel plate gussets. Construction: Full-penetration 360o TIG welded; one-piece gusseted main hoop and three-piece kicker; high-strength double-bolted interlocking roll bar joints and American-made Grade 8 hardware. CNC-cut precision mounting plates Full seat travel with any seat Detailed installation instructions & all necessary hardware for a seamless installation This product is intended for off-road race track use only.

CMS Performance Clubsport Roll Bar For Porsche 992 GT3 & GT3RS This Roll Bar Fits The Following Cars: Porsche GT3, 992 (2022+) Porsche GT3RS, 992 (2023+) THE ULTIMATE NEW ROLL BAR FOR THE PORSCHE 992 GT3 & GT3RS Click Here for Installation Instructions The CMS Performance Clubsport Roll Bar is an exciting new variant of the incredibly popular GT3/GT3RS roll bar. Re-designed with steel gusseting and high-strength support tubing is added to the top and bottom of the X-brace and to all four corners, the CMS Performance Clubsport Roll Bar takes rigidity and strength to another level. This is the strongest, highest quality bolt-in roll bar on the market for the Porsche 992 GT3 and GT3RS, period. In designing and building the CMS Performance Clubsport roll bar, structural rigidity and impact protection were the primary goals. This roll bar is fully 360o TIG welded, the main tubing is 1.75" Docol R8 Advanced High-Strength Steel. CMS Performance is the only roll bar manufacturer to employ this modern material. The support tubing is Docol R8 as well, and the gussets are machined from steel plate. CMS Performance tailors the GT3/GT3RS Clubsport roll bar to take full advantage of the strongest chassis mounting points in the Porsche 992 GT3/GT3RS. The main roll hoop is X-braced and gusseted, with a single tube cross-bar providing lateral strength that's also used for mounting racing harness shoulder straps. ATTENTION TO DETAIL IS THE HALLMARK OF CMS PERFORMANCE The cross-bar on the CMS Performance Clubsport Roll Bar for the Porsche 992 GT3 and GT3RS lets you attach your racing harness shoulder straps at the proper angle (0° to -20° front-to-back) and distance relative to the driver and passenger, regardless of seat position. The CMS Performance Clubsport Roll Bar was designed to leave your rear view unobstructed by additional bracing that other roll bars require due to the use of inferior materials. CMS Performance also features a unique three-piece rear kicker that bolts to the Porsche 992 GT3/GT3RS rear shock towers (where the factory GT3 Cup Car roll cage mounts). These are the strongest rear mounting points, and also add rigidity to the chassis for more precise handling. This kicker design is incredibly strong while also being a breeze to install (typical one-piece designs can be a nightmare to install). The main roll hoop is mounted to your Porsche's steel frame structure beneath the vehicle just like the factory Cup Car cage. BUILT LIKE A TANK, FINISHED LIKE A PORSCHE Designed using the same guidelines as a full racing roll cage and fully 360o TIG welded by our chassis fabricators and master welders, the CMS Performance Clubsport Roll Bar for the Porsche 992 GT3 and GT3RS is unsurpassed in quality, durability, and structural integrity. Each roll bar is professionally powder-coated in-house to guarantee fit and finish no other manufacturer can match. This also lets us use powder coat colors we've matched to Porsche GT3 and GT3RS OEM paint colors for a truly customized aesthetic. We also offer custom technical powder coat finishes like the amazing Superchrome! Or you can choose our rich satin black powder coat for a more low-key installation. Powder coating any color you choose is included in the price of your CMS Performance roll bar. DON'T SETTLE FOR ANYTHING BUT THE VERY BEST Thoughtful engineering and design, superior materials, masterful fabrication, and beautifully customized finishing. That's the CMS Performance way of doing things. Backed by our legendary customer service, it all adds up to this: you can pay more for a roll bar, but you can only get the best from CMS. ADD PREMIUM RACING HARNESSES TO YOUR PORSCHE Add six-point Schroth Enduro 2x2 GT3, Schroth Flexi 2x2 GT3, or Sabelt Silver Series GT3 racing harness to your order and save! These harnesses are specifically designed for the Porsche 992 GT3 and GT3RS and will bolt to your factory lightweight carbon bucket seats. Or you can add four-point Schroth Profi II ASM GT3 or Sabelt Porsche GT3 4 Point harnesses, ideal for the Porsche 992 GT3 and GT3RS passenger seat that doesn't have a factory sub-strap pass through. With six-point harnesses, we strongly recommend using the CMS Performance Sub Strap Mount to provide a solid, properly located anchor for your anti-submarine straps. The CMS Performance Sub Strap Mount is simple to install at the same time you're installing your roll bar! STRAIGHTFORWARD INSTALLATION TAKES THE HEADACHE OUT OF A ROLL BAR We've been through more than a few wrestling matches installing bolt-in roll bars in street cars. Fortunately, we used that experience to design the CMS Performance Roll Bar for the Porsche 992 GT3 and GT3RS to be a lot less frustrating to install. Check out the installation instructions here. We hesitate to go so far as to say it's easy, but we'll say it isn't hard if you have a friend and some basic tools. CMS PERFORMANCE PORSCHE 992 GT3/GT3RS CLUBSPORT ROLL BAR DETAILS Manufacturer: CMS Performance Manufacturer Part: CPRB-992CS Materials: Docol R8 Advanced High-Strength Steel; steel plate gussets. Construction: Full-penetration 360o TIG welded; one-piece gusseted main hoop and three-piece kicker; high-strength double-bolted interlocking roll bar joints and American-made Grade 8 hardware. CNC-cut precision mounting plates Full seat travel with any seat Detailed installation instructions & all necessary hardware for a seamless installation This product is intended for off-road race track use only.

CMS Performance Deluxe Bolt-In Harness Bar For C8 Corvette This Harness Bar Fits the Following Cars: Chevrolet Corvette Stingray & Z51 (2020+) Chevrolet Corvette Z06 (2023+) Does not fit convertible models A HARNESS BAR BUILT TO THE SAME EXACTING STANDARDS AS YOUR C8! The C8 Corvette is an incredible, affordable track-day car that easily achieves race car performance on track. Managing that kind of performance wearing nothing but a three-point seat belt is a chore and leaves a lot to be desired in terms of safety. That's where we come in with the CMS Performance C8 Corvette Deluxe Harness Bar. Featuring the same rock-solid, high-strength design as our standard C8 Harness Bar, the Deluxe bar adds an innovative "main hoop" design, giving it a more aggressive look. This also gives you a place to mount an in-car motorsports video camera, like the AiM Sports SmartyCam GP HD. Of course, it provides high-strength mounting points for your harness shoulder straps to keep you firmly and safely in your seat. The CMS Performance C8 Deluxe Harness Bar is the strongest, most elegantly designed C8 harness bar on the market. It seamlessly integrates into your C8 interior, preserves your rear view, and gives the C8 a big bump in cool factor, especially with a custom powder-coat color! The CMS C8 Deluxe Harness Bar allows full seat travel while locating your harness shoulder belts at the proper height for maximum on-track safety and security. Click Here For Installation Instructions Installation requires no drilling or other modification of the chassis, and no modification of your upper center console trim. Some modification of your B-pillar lock/seat belt trim panels is required. We offer precision pre-cut panels to ease installation and save your originals if you need to put your C8 back to stock. THE BEST C8 HARNESS BAR IS DESIGNED AND BUILT IN AMERI CA Every CMS Performance Deluxe Harness Bar for the C8 Corvette is painstakingly designed and hand-crafted in America by master racing fabricators. This guarantees you a superior product and perfect fit. The CMS Performance Deluxe Harness Bar is meticulously 360o TIG welded for high strength, and fully powder-coated in our facility for a brilliant, durable finish. And there's no extra charge for custom colors. CMS operates a complete powder-coating facility to offer you color-matched Corvette factory colors, giving your C8 a customized look that will last. CNC mandrel bent and fully TIG welded from premium Docol R8 Advanced High-Strength Steel (stronger than 4130 CrMo or DOM) and finished in rich powder coating. Complete, detailed instructions make installation pretty simple (figure about an hour if you're reasonably handy). Add optional four-point Schroth Profi II ASM Harnesses and our Harness Installation Kit, and you're ready to hit the race track. These harnesses were specifically designed for use in street cars with no sub strap pass-through in the seat. CMS PERFORMANCE C8 DELUXE HARNESS BAR DETAILS: Manufacturer: CMS Performance Manufacturer part no.: CPHB-C8DLX Material: 1.50 x .095 Docol R8 Advanced High-Strength Steel Construction: full 360o TIG welding Finish: custom powder coating is included, any color you can imagine! Weight: 24 lbs. (10.9 kg) Features: unobstructed rear view; designed, built, and powder coated in the USA; allows full seat travel with any seat Installation: includes all necessary hardware This product is intended for off-road use only.

Adjustable Sway Bar Kit for Porsche 981 Cayman & Boxster SEE INSTALLATION INSTRUCTIONS HERE Through extensive research and track testing, CMS has engineered the perfect replacement sway bars for the Porsche 981 Cayman/Boxster (GT4/Spyder, GTS, S, or base model)1. Our engineers took hundreds of laps at racetracks from Road America to COTA, Mid Ohio to High Plains, along with thousands of miles on the street. All to confirm the CMS Performance Sway Bars transform the handling of the Porsche 981 while maintaining the car's everyday driveability and reliability. Tuned to work with your Porsche's OEM struts and springs (both standard and PASM), the CMS Sway Bars are the best handling improvement you can make to your 981. Based on the sway bars of the GT4, the CMS Performance Sway Bars have five holes of adjustment both front and rear, giving you an unprecedented range within which to tune your car's handling depending on the road or track you're tackling. Slightly larger than the OEM GT4 bars, they can be adjusted from slightly softer than stock to substantially stiffer. This lets you fine-tune handling balance from understeer to neutral to oversteer with simple hand tools. Included are OEM Porsche sway bar bushings, precision-machined for the slightly larger bars, giving you worry-free fitment, OEM quality, and a noise-free installation. CMS Performance Sway Bars are engineered and manufactured in the USA with drop-forged ends for high strength and performance. Original Cayman GT4 and Boxster Spyder drop links, both front and rear, work perfectly with CMS Performance Sway Bars; no need to replace them. Base, S, GTS models require CMS front drop links (choose from the options above). These are OEM Porsche front links customized to fit the CMS front sway bar. Your original rear drop links do not need to be replaced. FITMENT:   981 Boxster/Cayman all incl. GT4/Spyder (2012-2016) Manual  and PDK Transmission (includes spacers for rear fitment on PDK cars)     FEATURES: Diameters of 31.8mm (front) and 25.4mm (rear), 30% larger than the OEM 981 Cayman GT4 bars Adjustment of each bar goes from 1% softer than stock to 50% stiffer. Powder-coated Black, Red, Yellow, or Silver for long life and great looks Designed and manufactured in the USA using all US components Engineered specifically for the Porsche 981     KIT INCLUDES: Front and rear five-way-adjustable sway bars w/ forged ends OEM Porsche bushings custom-machined to our specifications Optional: OEM Porsche front drop link set, customized to our specification (required for Base, S, GTS)  

CMS Performance Bolt In Roll Bar For BMW F82 M4 This Roll Bar Fits the Following Cars: BMW M4 F82 2015-2020 Carbon Roof BMW M4 Competition 2016-2020 Carbon Roof The Strongest and Safest Roll Bar for the BMW F82 M4 The CMS Performance Roll Bar is the strongest, safest, most beautifully constructed bolt-in roll bar on the market for the BMW M4 and M4 Competition. Engineered with a premium on safety and structural rigidity, the exceptional design integrates perfectly with the M4's luxury/sport interior. CMS uses only advanced Docol R8 Advanced High-Strength Steel tubing throughout each roll bar, giving you unequalled tensile strength and occupant protection. Docol R8 is 15% stronger than 4130 CrMo steel and 30% stronger than mild (DOM) steel used in other bolt-in roll bars. It is superior in every way: resistance to deformation, weld strength, and energy dissipation. Our one-piece main hoop with fully-integrated X-bracing and harness bar bolts directly to the chassis, forming the backbone of the CMS Performance Roll Bar. Rearward "kicker" supports are optimized for support in a roll-over event while maintaining an unobstructed rear view. The harness bar is specifically designed to locate racing harness shoulder straps at the proper angle (0° to -20°) to the driver's shoulders regardless of seat position. Cutting Edge Materials and American-Made Craftsmanship Click Here for Installation Instructions The CMS Performance BMW M4 Roll Bar is designed to bolt directly to the M4 chassis strong points without the need for any modification of existing interior trim or use of backing plates. Adding a CMS custom designed rear seat delete gives the whole installation a clean, factory appearance. Full 360o TIG welding throughout gives the CMS Performance Roll Bar unsurpassed strength and durability. Each roll bar includes custom powder coating in your choice of matched M4 factory colors. You can choose an amazing technical color like Superchrome! Or satin black for a more stealthy appearance. We have over 5,000 custom powder coat colors for a truly customized look. Our unwavering focus on using cutting-edge materials, unsurpassed design & construction, and premium fit & finish has taken CMS Performance Roll Bars to the top of the industry. The BMW M4 roll bar is the latest addition to our growing catalog, bringing safety, integrity, and beauty to customers taking their M4 to the track! CMS Performance BMW F82 M4 Roll Bar Options CMS premium Rear Seat Delete Kit is custom-designed for the F82 M4, giving your roll bar installation a factory-finished look. CMS Roll Bar Harness Collars help keep your harness shoulder straps where you want them. CMS Performance BMW F82 M4 Roll Bar Details Manufacturer: CMS Performance Materials: 1.75″ X .095" Docol R8 Advanced High Strength Steel tubing throughout Construction: One-piece main hoop and three-piece kickers ease installation while maintaining exceptional strength Included hardware: Grade 8, American made CMS Performance BMW F82 M4 Roll Bar Features Optional premium custom-designed rear seat delete for a factory-finished appearance Precision-cut mounting plates Designed, manufactured, and finished in the USA American-made CNC machined solid steel interlocking joints Allows full seat travel with virtually any seat Comes with detailed installation instructions Installation requires removal of the factory rear seats. A rear seat delete kit is recommended but not required for roll bar installation. This product is intended for off-road race track use only.

CMS Performance Bolt-In Harness Bar For C8 Corvette This Harness Bar Fits the Following Cars (does not fit convertible): Chevrolet Corvette Stingray, C8 (2020+) Chevrolet Corvette Z06, C8 (2023+) THE ROLL BAR AS AWESOME AS THE C8 ITSELF! The C8 Corvette is an incredible, affordable supercar that easily achieves race car performance on track. Maintaining driver safety with that kind of performance wearing nothing but the three-point seat belt is a chore and leaves a lot to be desired in terms of safety. That's where we come in with the CMS Performance C8 Corvette Harness Bar. This provides a rock-solid, high-strength bar to mount shoulder straps for a 4-, 5-, or 6-point racing harness to keep you firmly and safely in your seat. The CMS Performance C8 Harness Bar is the strongest, most elegantly designed C8 harness bar on the market. It seamlessly integrates into your C8 interior, and we custom powder coat it whatever color you choose, including factory color-matched hues. The CMS C8 bar allows full seat travel while locating your harness shoulder belts at the proper height for maximum on-track safety and security. Click Here For Installation Instructions Installation requires no drilling or other modification of the chassis, and only minor modification of your interior trim. You can add our precision pre-cut OEM trim to ease the install, preserving your original trim should you want to put your Corvette back to stock in the future. PREMIUM QUALITY AND EXCEPTIONAL PERFORMANCE Every CMS Performance C8 Corvette Harness Bar is designed and hand-crafted in the USA by race chassis fabricators for a perfect fit, beautifully 360o TIG welded for high strength, and fully powder coated in the CMS Performance facility for a brilliant, durable finish. There's no extra charge for color-matched Corvette factory colors, giving your C8 a customized look that will last. CNC mandrel bent and fully TIG welded from premium Docol R8 Advanced High-Strength Steel (stronger than 4130 CrMo and mild steel) and finished in a rich powder coat color. Complete, detailed instructions make installation pretty simple (figure about an hour if you're reasonably handy). Installation requires modifying the two lock/seat belt trim panels and the upper trim of your center console. We offer two levels of pre-cut trim to ease installation: first, just the upper console (the most visible and most difficult to trim correctly); second the upper console plus the two lock/seat belt trim panels. Our installation instructions also include cutting templates should you decide to modify your existing trim. Add optional four-point Schroth Profi II ASM Harnesses and our Harness Install Kit, and you're ready to hit the track. These harnesses were specifically designed for use in street cars with no sub strap pass-through in the seat. CMS PERFORMANCE C8 CORVETTE HARNESS BAR DETAILS: Manufacturer: CMS Performance Manufacturer part no.: CPHB-C8PR Material: 1.50" x .095" Docol R8 Advanced High-Strength Steel Construction: Full 360o TIG welded Finish: Custom-color powder coating is included Weight: 18 lbs. (8.2 kg) Unobstructed rear view Designed, built, and finished in the USA Allows full seat travel with any seat Includes all necessary hardware This product is intended for off-road use only.

CMS Performance Harness Install Kit For C7 Corvette This Product Fits The Following Cars: Chevrolet Corvette Stingray & Z51, C7 (2014-2019) Chevrolet Corvette Z06, C7 (2015-2019) Quick and Easy Installation of Harness Lap Belts in the C7 Corvette The CMS Performance Harness Install Kit for the C7 Corvette provides two strong, secure anchors for the lap belts of your racing harness using the factory seats of your C7 Corvette. Each CMS Performance C7 Corvette Harness Install Kit is for one seat (driver or passenger side, the kit works on either seat). Ordering two kits saves you $25 overall and you can install a harness for your passenger or instructor. CMS Performance is 100% Designed and Built in the USA All CMS Performance products are designed, constructed, and finished in our USA manufacturing and powder coating facility. The CMS Performance C7 Corvette Harness Install Kit is CNC cut and fully TIG-welded from high-strength stainless steel, then powder coated a rich satin black to blend seamlessly into your interior when you don't have harnesses installed. Complete detailed instructions make installation straightforward (figure about an hour if you're reasonably handy). Click here for installation instructions. For the C7 Corvette, we recommend the Schroth Profi II ASM or Sabelt Steel Series four-point harnesses for use with this kit. Schroth's proprietary Anti-Submarine (ASM) technology was developed specifically for use in street cars like the C7 Corvette without a sub strap a pass-through in the seats. Sabelt's four point Steel Series offers an alternative that gives you a significant safety upgrade at a reasonable price! CMS Performance Harness Install Kit Details: Manufacturer: CMS Performance manufacturer Part: Harninstall-C7 Construction: 360o TIG welded stainless steel Finish: Satin black powder coat Designed, manufactured, and powder coated by CMS Performance in the USA This product is intended for off-road use only.

CMS Performance Harness Install Kit For C8 Corvette This Product Fits The Following Cars: Chevrolet Corvette Stingray & Z51, C8 (2020+) Chevrolet Corvette Z06, C8 (2023+) Quick and Easy Installation of Harness Lap Belts in the C8 Corvette The CMS Performance Harness Install Kit for the C8 Corvette provides two strong, secure anchors for the lap belts of your racing harness using the factory seats of your C8 Corvette. The kit is typically used along with the CMS Performance C8 Harness Bar or Deluxe C8 Harness Bar. Together they give C8 Corvette driving enthusiasts an elegant, secure way to use a racing harness. Each CMS Performance C8 Corvette Harness Install Kit is for one seat (driver or passenger side, the kit works on either seat). Ordering two kits now, you save $25 and you can install a harness for your passenger or instructor. CMS Performance is 100% Designed and Built in the USA All CMS Performance products are designed, constructed, and finished in our USA manufacturing and powder coating facility. The CMS Performance C8 Corvette Harness Install Kit is CNC cut and fully TIG-welded from high-strength stainless steel, then powder coated a rich satin black to blend seamlessly into your interior when you don't have harnesses installed. Complete detailed instructions make installation straightforward (figure about an hour if you're reasonably handy). Click here for installation instructions. For the C8 Corvette, we recommend the Schroth Profi II ASM Harness for use with this kit. Schroth's proprietary Anti-Submarine (ASM) technology was developed specifically for use in street cars like the C8 Corvette that don't have a pass-through in the seat cushions to accommodate the sub straps of a six-point racing harness. CMS Performance Harness Install Kit Details: Manufacturer: CMS Performance manufacturer Part: Harninstall-C8 Construction: 360o TIG welded stainless steel Finish: Satin black powder coat Designed, built, and powder coated in the USA This product is intended for off-road use only.

CMS Performance Harness Install Kit For Gen 6 Camaro This Product Fits The Following Cars: Chevrolet Camaro Coupe, all (2016+) Quick, Easy Installation of Harness Lap Belts in the Gen 6 Camaro The CMS Performance Harness Install Kit for the Gen 6 Camaro provides two strong, secure anchors for the lap belts of your racing harness using the factory seats of your Gen 6 Camaro. Each CMS Performance Gen 6 Camaro Harness Install Kit is for one seat (driver or passenger side, the kit works on either seat). Ordering two kits saves you $25 overall and you can install a harness for your passenger or instructor. CMS Performance is 100% Designed and Built in the USA All CMS Performance products are designed, constructed, and finished in our USA manufacturing and powder coating facility. The CMS Performance Gen 6 Camaro Harness Install Kit is CNC cut and fully TIG-welded from high-strength stainless steel, then powder coated a rich satin black to blend seamlessly into your interior when you don't have harnesses installed. Complete detailed instructions make installation straightforward (figure about an hour if you're reasonably handy). Click here for installation instructions. For the Gen 6 Camaro, we recommend the Schroth Profi II ASM or Sabelt Steel Series four-point harnesses for use with this kit. Schroth's proprietary Anti-Submarine (ASM) technology was developed specifically for use in street cars like the Gen 6 Camaro without a sub strap a pass-through in the seats. Sabelt's four point Steel Series offers an alternative that gives you a significant safety upgrade at a reasonable price! CMS Performance Harness Install Kit Details: Manufacturer: CMS Performance manufacturer Part: Harninstall-G6C Construction: 360o TIG welded stainless steel Finish: Satin black powder coat Designed, manufactured, and powder coated by CMS Performance in the USA This product is intended for off-road use only.

CMS Performance Bolt-In Harness Bar for Porsche 981 & 718 Cayman This Harness Bar Fits The Following Cars: Porsche Cayman (2014+) Porsche Cayman S (2014+) Porsche Cayman GTS (2015+) Porsche Cayman GT4 (2016+) Porsche Cayman GT4 RS (2022+) High Strength Bolt In Harness Bar For Your Porsche Cayman Expertly crafted from high-strength, fully TIG welded Docol R8 Advanced High-Strength Steel tubing, the CMS Performance Porsche Cayman Harness Bar is the strongest, lightest, and safest bolt-in harness bar on the market for your Porsche 981 Cayman. It gives you the perfect attachment for your five- or six-point harness shoulder straps without having to install a full roll bar. The CMS Performance Porsche Cayman Harness Bar is designed to place your racing harness shoulder straps at the proper angle (0° to -20°) and distance (eight inches or less) so the driver and passenger racing harnesses function properly. There is no need to cut your Porsche Cayman's carpeted central hump, a design unique to CMS Performance that provides an ideal location for mounting an AiM SmartyCam. The CMS Performance Porsche Cayman Harness Bar also gives you full access to the engine cover. It mounts to the frame structure across the passenger compartment bulkhead, directly behind the seats. Click Here For Installation Instructions Made In The USA For The Ultimate In Quality And Precision The CMS Performance Porsche Cayman Harness Bar is meticulously designed, fabricated, and fully TIG welded by CMS Performance master fabricators for unsurpassed integrity, fit, and finish. The harness bar comes standard in a smooth satin black powder coat to complement any interior. Or you can choose from any number of custom powder coat colors matched to most factory Porsche paint colors. To install the CMS Performance Porsche Cayman Harness Bar, some modification of your OEM interior trim will be required. CMS Performance offers precision-cut OEM Porsche trim as an option to ease installation and preserve your original interior pieces. Features Of The CMS Performance Porsche Cayman Harness Bar: 1.50″ x .120" Docol R8 Advanced High-Strength Steel No cutting of carpeted center hump preserves expensive OEM carpet CNC-cut mounting plates Designed and built in the USA Allows full seat travel with any seat Easy to install with perfect fitment guaranteed Detailed Installation Instructions and all necessary hardware included

Rear Seat Delete for BMW F87 M2 Complete your CMS Performance roll bar installation with this custom-made rear seat delete kit for the BMW F87 M2. Made from high-strength ABS plastic and upholstered to match the look of your BMW M2 interior. Set includes seat back and two seat-bottom replacement panels.  

Rear Seat Delete for BMW G87 M2 Complete your CMS Performance roll bar installation with this custom-made rear seat delete kit for the BMW G87 M2. Made from high-strength ABS plastic and upholstered to match the look of your BMW G87 M2 interior. Set includes seat back, two seat-bottom replacement panels, brackets and plastic push fasteners.  

CMS Performance Bolt In Roll Bar For BMW E92 M3 (2008-13) A PREMIUM BOLT-IN ROLL BAR FOR THE LEGENDARY E92 The CMS Performance Roll Bar is the strongest, safest, most beautifully constructed bolt-in roll bar on the market for the BMW E92 M3. It is engineered to easily bolt into any E92 variant, providing you with both the rollover protection of a super-strong roll bar and the beauty and craftsmanship for which CMS Performance is renowned. Engineered with a premium on safety and structural rigidity, the exceptional design integrates perfectly with the M3's luxury/sport interior. CMS uses only advanced Docol R8 Advanced High-Strength Steel tubing throughout each roll bar, giving you unequalled tensile strength and occupant protection. Docol R8 is 15% stronger than 4130 CrMo steel and 30% stronger than mild (DOM) steel used by other roll bar manufacturers. It is superior in every way: resistance to deformation, weld strength, and energy dissipation. Our one-piece main hoop with fully-integrated X-bracing and harness bar bolts directly to the chassis, forming the backbone of the CMS Performance Roll Bar. Rearward "kicker" supports are optimized for support and easy installation while maintaining an unobstructed rear view. The harness bar is specifically designed to locate racing harness shoulder straps at the proper angle (0° to -20°) in most seating positions. CUTTING EDGE MATERIALS & DIRECT BOLT-IN Click Here for Installation Instructions The CMS Performance BMW E92 M3 Roll Bar is designed to bolt directly to the M3 chassis' strong points without the need for any modification of existing interior trim or use of backing plates. Adding a CMS custom designed rear seat delete gives the whole installation a clean, factory appearance. Full 360o TIG welding throughout gives the CMS Performance Roll Bar unsurpassed strength and durability. Each roll bar includes custom powder coating in your choice of matched M3 factory colors, satin black for a more stealthy appearance, or any of over 5,000 custom powder coat colors for a truly customized look. Our unwavering focus on using cutting-edge materials, unsurpassed design & construction, and premium fit & finish has taken CMS Performance Roll Bars to the top of the industry. The BMW E92 M3 roll bar is the latest addition to our growing catalog, bringing safety, integrity, and beauty to your M3 whether on the street or at the track! CMS PERFORMANCE BMW E92 M3 ROLL BAR OPTIONS Main hoop X-brace gussets (as shown in photos) can be added for $200. Schroth Profi II ASM four-point harnesses have a patented anti-submarine design to give you racing harness safety with your factory BMW seats. Roll Bar Harness Collars help keep your shoulder straps where you want them. CMS PERFORMANCE BMW E92 M3 ROLL BAR DETAILS 1.75″ X .090" Docol R8 Advanced High Strength Steel throughout (stronger than 4130 CrMo) One-piece main hoop for superior strength and occupant safety Three-piece kickers ease installation while maintaining exceptional strength Precision-cut mounting plates Designed and TIG welded in the USA by master racing fabricators CNC machined high-strength-steel interlocking joints Allows full seat travel with virtually any seat All USA-made Grade 8 hardware included Comes with detailed installation instructions Installation requires removal of the factory rear seat bottom cushion. This product is intended for off-road use only.

CMS Performance Bolt In Roll Bar For BMW F87 M2 (2016-2021) This Roll Bar Fits the Following Cars: BMW M2 (N55) 2016-2018 BMW M2 Competition (S55) 2019-2020 BMW M2 CS 2020-2021 THE PREMIER BOLT-IN ROLL BAR FOR THE ICONIC M2 The CMS Performance Roll Bar is the strongest, safest, most beautifully constructed bolt-in roll bar on the market for the BMW M2, M2 Competition, and M2 CS. Engineered with a premium on safety and structural rigidity, the exceptional design integrates perfectly with the M2's luxury/sport interior. CMS uses only advanced Docol R8 Advanced High-Strength Steel tubing throughout each roll bar, giving you unequalled tensile strength and occupant protection. Docol R8 is 15% stronger than 4130 CrMo steel and 30% stronger than mild (DOM) steel used in other bolt-in roll bars. It is superior in every way: resistance to deformation, weld strength, and energy dissipation. Our one-piece main hoop with fully-integrated X-bracing and harness bar bolts directly to the chassis, forming the backbone of the CMS Performance Roll Bar. Rearward "kicker" supports are optimized for support in a roll-over event while maintaining an unobstructed rear view. The harness bar is specifically designed to locate racing harness shoulder straps at the proper angle (0 to -20 ) to the driver's shoulders regardless of seat position. The CMS Performance BMW M2 Roll Bar is designed to bolt directly to the M2 chassis strong points without the need for any modification of existing interior trim or use of backing plates. Adding a CMS custom designed rear seat delete gives the whole installation a clean, factory appearance. Full 360o TIG welding throughout gives the CMS Performance Roll Bar unsurpassed strength and durability. Each roll bar includes custom powder coating in your choice of matched M2 factory colors, satin black for a more stealthy appearance, or any of over 5,000 custom powder coat colors for a truly customized look. Our unwavering focus on using cutting-edge materials, unsurpassed design & construction, and premium fit & finish has taken CMS Performance Roll Bars to the top of the industry. The BMW M2 roll bar is the latest addition to our growing catalog, bringing safety, integrity, and beauty to customers taking their M2 to the track! Click Here for Installation Instructions CMS PERFORMANCE BMW F87 M2 ROLL BAR OPTIONS CMS premium Rear Seat Delete Kit is custom-designed for the F87 M2, giving your roll bar installation a factory-finished look. Schroth Profi II ASM four-point harnesses have a patented anti-submarine design to give you racing harness safety with your factory BMW seats. CMS Roll Bar Harness Collars help keep your shoulder straps safely and securely in place on the harness cross-bar. CMS PERFORMANCE BMW F87 M2 ROLL BAR DETAILS Manufacturer: CMS Performance Manufacturer part no.: CPRB-F87 Materials: Docol R8 Advanced High Strength Steel tubing 1.75 x 0.095; CNC-cut carbon steel mounting plates; CNC-machined solid steel interlocking roll bar joints Construction: full penetration 360º TIG welding Design features: one-piece main hoop for strength; three-piece kickers ease installation; allows full seat travel with virtually any seat Optional custom-designed rear seat delete All American-made Grade 8 hardware included Detailed installation instructions Installation requires removal of the factory rear seats. A rear seat delete kit is recommended but not required for roll bar installation. This product is intended for off-road use only.

CMS Performance Bolt In Roll Bar For BMW G87 M2 (2023+) THE PREMIUM ROLL BAR FOR THE POWERFUL NEW M2 Introducing the CMS Performance Roll Bar for the all-new, amazing G87 M2*.  The powerful new M2 promises to be a hoot on the track-day circuit, so we got to work right away engineering a bolt-in roll bar that lives up to Competition Motorsport's tradition of building the strongest, safest, most beautifully constructed roll bars on the market. The new CMS Performance roll bar for the G87 delivers on all points! ENGINEERED FOR SAFETY AND PERFORMANCE Click Here for Installation Instructions Conceived from the ground up with a premium on safety and structural rigidity, the exceptional design of the CMS Performance M2 roll bar integrates perfectly with the M2's luxury/sport interior. CMS Performance uses advanced Docol R8 Advanced High-Strength Steel tubing throughout our roll bars, giving you unequalled tensile strength and occupant protection. Docol R8 is 15% stronger than 4130 CrMo steel and 30% stronger than mild (DOM) steel used in other bolt-in roll bars. It is superior in every way: resistance to deformation, weld strength, and energy dissipation. The one-piece main hoop with fully-integrated X-bracing and harness bar bolts directly to the M2 chassis, forming the backbone of the CMS Performance roll bar. Rearward kicker supports are optimized for support in a roll-over event while maintaining an unobstructed rear view. The harness bar is specifically designed to locate racing harness shoulder straps at the proper angle (0° to -20°) to the driver's shoulders regardless of seat position. CUTTING EDGE MATERIALS, DIRECT BOLT-IN The CMS Performance BMW M2 Roll Bar is designed to bolt directly to the M2 chassis strong points without the need for any modification of existing interior trim or use of backing plates. Adding a CMS custom designed rear seat delete gives the whole installation a clean, factory appearance. Full 360o TIG welding throughout gives the CMS Performance Roll Bar unsurpassed strength and durability. Each roll bar includes custom powder coating in your choice of matched G87 M2 factory colors. Or you can choose a standard color like Satin Black (for a stealthy install). We have access to over 5,000 powder coat colors, so if you need a color not on the list, just give us a call and we'll make sure your M2 roll bar has the look you like! BRAUN AND BEAUTY COMBINED Our unwavering focus on using cutting-edge materials, unsurpassed design & construction, and premium fit & finish has taken CMS Performance roll bars to the top of the industry. The BMW G87 M2 roll bar is the latest addition to our growing catalog, bringing safety, integrity, and beauty to customers taking their new M2 to the track! * Note: This roll bar does not fit cars equipped with the optional factory sunroof. CMS PERFORMANCE BMW G87 M2 ROLL BAR DETAILS Manufacturer: CMS Performance Materials: Docol R8 advanced high-strength steel tubing, 1.75 x 0.095; CNC-cut carbon steel mounting plates; CNC-machined solid steel interlocking roll-bar joints Construction: full penetration 360º TIG welding Finish: powder coat, custom colors at no extra charge Rear seat delete: optional Design features: one-piece main roll hoop with six-point bracing; three-piece support kickers to ease installation Hardware included: all necessary American-made Grade 8 installation hardware BMW G87 M2 Roll Bar Features & Options: Optional custom-designed rear seat delete for a factory-finished appearance Factory powder coat colors plus custom finishes at no additional charge Schroth Profi II ASM four-point harnesses have a patented anti-submarine design to give you racing harness safety with your factory BMW seats Roll Bar Harness Collars help keep your shoulder straps where you want them Allows full seat travel with virtually any seat Detailed installation instructions Installation requires removal of the factory rear seats. This product is intended for off-road use only.

CMS Performance Bolt-In Roll Bar For Gen 6 Chevy Camaro Fits the Following Cars: Gen 6 Chevy Camaro (2016+) all except convertible STRONGEST ROLL BAR AVAILABLE FOR GEN 6 CAMARO The CMS Performance Camaro Roll Bar is the strongest, safest, and most beautifully constructed roll bar on the market. In designing the Camaro roll bar, safety, strength, and structural integrity were our primary goals. Fully TIG welded from Docol R8 Advanced High-Strength Steel allows us to design a roll bar that is stronger and lighter! Our innovative design maximizes the room for the factory Recaro seats, meaning taller drivers can send their seat all the way back and still maintain a comfortable recline. Precision CNC machined solid steel interlocking roll bar clamps on the kicker mounting plates help make installation a snap. Free custom powder-coating gives you a premium, finished look without breaking the budget. Add the optional custom-cut Rear Seat Delete Kit and you've got a fully trimmed-out roll bar installation that performs as great as it looks. Our Camaro roll bar forms the perfect foundation for taking your safety up a huge notch. Click Here for Installation Instructions SAFETY IS OUR FIRST PRIORITY Safety is the main reason to install a roll bar in the first place. As racers ourselves, we sweat the details. That's why we use 1.75" x .095" Docol R8. Docol is 15% stronger than 4130 CrMo, and much less brittle. Docol R8 also dissipates impact energy more effectively. It's the same tubing used in full-competition road racing roll cages because, first and foremost, it's a roll bar not a trim piece. Our beefy main hoop straddles the rear seat cross member, a much stronger location than the rear footwell, eliminating the need for underbody backing plates. Taking a cue from NHRA cage design, the diagonal supports feature a concave design to allow full front-seat travel while distributing roll-over energy between the main hoop and kickers. The harness cross-bar is precisely located to put your shoulder straps at both the proper angle (0 to -20 ) and distance to the driver. Finally our rear kickers bolt to a reinforced corner of the rear seat floor, again requiring no backing plates beneath the floor pan. A clear rear view is a safety concern. Our use of stronger materials and innovative design lets us keep your rear view unobstructed by additional bracing. This also helps weight down. Every detail of the CMS Gen 6 Camaro roll bar is engineered with safety as our primary goal. HAND CRAFTED IN AMERICA Okay, another reason people install a roll bar is that they look cool. We're car guys, we get that. Each roll bar is handcrafted right here in America by master fabricators for a perfect fit, beautifully 360o TIG welded for high strength, and fully powder-coated in our facility for a brilliant, durable finish. There's no extra charge for custom colors. CMS operates a complete powder-coating facility to offer you color-matched Camaro factory colors, giving your Camaro a personalized look that will last. None of your interior trim panels need to be eliminated or cut. Your rear seat back can be re-installed, or you can opt for our custom Shrader rear seat delete, the perfect place to put a track bag, helmet and HANS, driver cooling system, etc. (you can hide stuff under there, too). If you ever want to put your car back to stock, it will go back together as though the roll bar was never there. Complete, detailed instructions make installation pretty simple (figure about two hours if you're reasonably handy), and all Grade 8 hardware needed is shipped with your CMS roll bar. Add Racing Harnesses and a Head-And-Neck Restraint and and you're ready to hit the track safe and secure. CMS PERFORMANCE GEN 6 CAMARO ROLL BAR DETAILS Manufacturer: CMS Performance Manufacturer part no.: CPRB-CamaroG6 Materials: Docol R8 Advanced High-Strength Steel tubing 1.75 x .095; CNC-cut carbon steel mounting plates;  CNC-machined solid steel interlocking roll bar joints Construction: full-penetration 360o TIG welding Hardware included: all necessary American-made Grade 8 hardware Design features: one-piece main hoop/kicker design with detachable kicker feet for installation Weight: 51 lbs. (23.1 kg) Custom-made rear seat delete available Designed, built, and powder-coated in the USA Allows full seat travel with any seat This product is intended for off-road use only.